Bedienungsanleitung Roblin Lido (Seite 10 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490295

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

chimney stacks to the brackets using the two M4 screws item 12c provided. Fit the lower chimney

sections by expanding the chimneys slightly to allow them from the top of the canopy to clamp around

the upper chimney sections.

IN THE RECIRCULATION MODE:

a. Fit the recirculation spigot R onto the upper chimney wall bracket using the same xing screws (Fig.

2 item 2).

b. Connect the ducting 150mm (6 INS) not provided between motors item 6 and the recirculation spigot

and secure the connections with appropriate clamping rings or adhesive tape.

c. Remove the grease lters (see paragraph Maintenance) Fig. 5 being sure that the connector of the

feeding cable is correctly inserted in the socket placed on the side of the fan. Before tting the chimney

to the canopy make the electrical connection as described in the section titled ELECTRICAL. When

the electrical connection has been made, test the lights and the fan motor.

d. Insert the charcoal lter into the base of the motor housing and secure the lter with two metal secur-

ing straps item A as illustrated in Fig. 4.

e. Each chimney stack consists of two sections. Fit the upper sections (Fig. 1 - item 7a & b) rst by

expand-ing the chimneys slightly to allow them to clamp around the bracket item 2 and secure the

chimney stacks to the brackets using the two M4 screws item 12c provided. Fit the lower chimney

sections by expanding the chimneys slightly to allow them from the top of the canopy to clamp around

the upper chimney sections.

4 OPERATION

A - EXTRACTION OR RECYCLING :Your cooker hood is supplied in the extraction mode. To use the cooker

hood in the recycling mode re-programme the hood as follows:

Starting in the recycling mode (the contaminated air passes into the hood through the grease lters and

the purifying activated charcoal lter and back out into the kitchen through grilles).

Press the ‘+’ button (while the motor and lights are switched ‘OFF’) until the ve LED lights will ash twice

to indicate conrmation that the cooker hood is in the recycling mode.

Reverting to the extraction mode (The cooker hood is ducted to the outside).

Press the ‘+’ button (while the motor and lights are switched ‘OFF’) until the ve LED lights will ash once

to indicate conrmation that the cooker hood is in the extraction mode.

B - BASIC INSTRUCTIONS

Lighting

Press LED button 1 to switch ‘ON’ the lights and the LED will illuminate to conrm the lights are switched

‘ON’.

Motor

Press LED button 2 to switch ‘ON’ the fan motor (and adjust the speed of the fan motor by pressing the

LED button ‘+’ and ‘-‘) and the LED lights 2, 3 and 4 will illuminate. The fan speed will be increased if

constant pressure is kept on the (+) button.

LED 2 : Minimum speed - cooking with one pan or simmering

LED 2 & 3 : Medium speed - normal cooking with up to 4 pans

LED 2, 3 & 4 : Maximum speed - frying and cooking foods with strong odours

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roblin Lido Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info