Bedienungsanleitung Roblin Windy Pro 1000 (Seite 9 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490282

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

markings identifying the terminals in your plug, proceed as follows.

- The wire which is coloured green and yellow must be connected to the terminal in the plug which is

marked with the letter E or by the earth symbol

or coloured green or green and yellow.

- The wire which is coloured blue must be connected to the terminal which is marked with the letter N

or coloured black.

- The wire which is coloured brown must be connected to the terminal which is marked with the letter

L or coloured red.

ATTENTION: Do not forget to use adequate plugs to the support brackets. Enquire after the manu-

facturers. Do an embedding if necessary. The manufacturer accepts no responsibility in case

of a faulty hanging due to the drilling and the setting up of plugs.

1) Draw a vertical line up the wall from the centre of the cooking appliance below as illustrated in g.

4 - item 1.

2) Mark a point on the vertical line which corresponds to the lower canopy position ( The height H of

the splashback item B is 402 mm ) and draw a horizontal line parallel to the stove top at a distance

of 580 - 18 mm above this point.

3) Mark the 2 hole centres for the canopy xing cup screws item T at a distance both left and right of

the vertical line of 312 mm as illustrated in g. 4.

4) Place one of the brackets g. 4, item 2 on the wall 2 mm from the ceiling or from the upper limited

of the chimney aligning the notches on the bracket centrally over the vertical line and mark the hole

centres

5) Place the second of the brackets item 2 on the wall aligning the notches on the bracket centrally

over the vertical line , at a distance X, which is equivalent to the height of the upper chimney section

item S, mark the hole centres and then drill the holes using an 8 mm masonry drill and x the cup

screws and the 2 brackets using the plastic rawl plugs provided.

6) Hook the canopy item C onto the cup screws item T as illustrated g. 2. The canopy should be se-

cured to the wall using the two key hole slots, whose centres are located 61 mm below cup screws.

Unhook the canopy, drill the holes using a 6.5 mm masonry bit and insert the rawl plug.

7) Draw a horizontal line through the vertical level with the back edge of the cooking surface. Place

the splashback against the wall onto the top of the cooking appliance. it could be x by rawl plugs

and screws on the bottom.

8) Hook the canopy item C onto the cup screws item T as illustrated in g. 2. The canopy can be ad-

justed horizontally and vertically ensuring the canopy aligns with the splashback and the cooking

appliance, by turning the adjustment screw item V. The canopy can be adjusted so that it aligns with

the wall by turning the adjustment screw item V2.

9) Secure the canopy to the wall using the security xing screw as illustrated in g. 3.

10) Place the noise-reduction tube item 4 over the round outlet on top of the canopy while pressing down

until it snaps into position ( Fig. 5), then the non-return backow aps item 3 over the noise-reduction

tube and duct the canopy to the outside using ducting 150 mm (6 ins) manufactured from re retard-

ant material , produced to BS.476 or DIN 4102-B1. Before tting the chimney to the canopy make

the electrical connection as described in the section titled ‘’ELECTRICAL WIRING’’, see as well UK

specications. When the electrical connection has been made , test the lights and the fan motor. Fit

the silent pack item 5 as illustrated in g. 6, operation 1 and 2 by clamping the two plastic rings on

either side of the motor diffuser and tting together noise-reduction casings and plastic rings.

IN THE REMOTE INSTALLATION MODE :

a. Connect the ducting 200 mm ( 8ins) onto the round outlets on the top of the canopy and onto the

round inlet of the motors at a distance and secure the connections with appropriate clamping rings

or adhesive tape.

b. Connect the earth connection onto the terminal marked with the earth symbol and clamp the connector

onto the motor housing as illustrated Fig. 12.

11)The chimney stack consists of two sections. Fit the upper section item S rst by expanding the chimney

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roblin Windy Pro 1000 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info