Bedienungsanleitung Roblin Windy Pro 900 (Seite 11 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490281

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Press LED button 5 to obtain the boost position for maximum effect and the LED C will illuminate to

conrm fan is switched ‘ON’.

C – COMPLEMENTARY INSTRUCTIONS

Automatic pre-set stop for the boost speed after 10 mn.

To obtain the best performance it is advisable to switch ‘ON’ the cooker hood a few minutes (in the

boost setting) before you start cooking and you should leave it running for approximately 10 minutes

after nishing.

Press LED button 5 to switch ‘OFF’ the fan motor immediately.

Indication of saturation of the metal grease lters

After 100 hours use, one quick ash of the LED F will indicate that you must clean the metal grease

lters. (See chapter on ‘Maintenance’).

This indication is not available when the fan motor is switched OFF.

Indication of saturation of the active charcoal lter

After 200 hours use, two quick ash of the LEDS F & C will indicate that you must replace the active

charcoal lter and clean the metal grease lters. (See chapter on ‘Maintenance’).

To reset the 200-hour timer the motor and lights must be switched ‘OFF’.

Push the LED button ‘+’ for 10 seconds.

One ash of the LED lights F and C = function is switched ‘OFF’.

Two ashes of the LED lights F and C = function is switched ‘ON’.

To reset the 100 hours timer back to zero requires the motor and lights must be switched ‘OFF’; then

and proceed as follows:

Press the LED button ‘+’ for 3 to 4 seconds and the LED lights F and C will ash to conrm the programme

has been reset to zero.

Instructions for replacing the active charcoal lter are given in the chapter on ‘Recycling’.

Setup Process

Modication: How to adjust the internal microprocessor data to suit the type of motor tted to

this appliance and the supply frequency of 50 or 60 Hz..

1 - Disconnect the cooker hood from the mains supply.

2 - Push the button 0/1 MOTOR.

3 - Reconnect the mains supply while pushing the button 0/1 MOTOR for at least 2 seconds.

4 - Slacken the button 0/1 MOTOR (the Leds ash for about 3 seconds : capacity’s

conrmation SETUP PROCESS).

5 - During the ashing time select the motor type used while pushing one of the 5 buttons

according to the following board:

BUTTON 0/1 Light : Motor FABER 8/28 & 8/50 220-240 V AC / 50 Hz.

BUTTON 0/1 Motor : Motor FABER 8/28 & 8/50 220-240 V AC / 60 Hz.

BUTTON Speed ( - ) : Motor EBM PRO 220-240 V AC / 50 Hz.

BUTTON Speed (+ ) : Motor EBM PRO 220-240 V AC / 60 Hz.

BUTTON Intensive speed : Motor K40 & K50 220-240 V AC / 50 Hz.

REMOTE CONTROL HANDSET

Caution, the remote control must be tted with standard LR03-AAA size 1.5V zinc-carbon alkaline bat-

teries as illustrated Fig. 8. These batteries should give a long life and constant discharge throughout

their life.

These batteries must be disposed of properly and could explode if damaged or exposed to heat.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roblin Windy Pro 900 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info