Bedienungsanleitung Robomow MC1200 - 2016 (Seite 39 von 58) (Englisch)

644655

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Screen Seng Descripon Opons

P022

Add Sub-Zone

• Enables the addition of a Sub-Zone. Maximal number of Sub-

Zones may be different for each Robomow model.

• A1/A2/A3/A4 (name of the rst available sub-zone) is displayed

- press OK.

• If the mower is not at the Base Station, then ‘U044’ (“Place the

mower in the Base Station”) is displayed. Place the mower in the

Base Station and press OK.

• The mower will start moving towards the Sub-Zone.

• Scroll to set the area of the Sub-Zone and press OK.

• Note! This process is not a part of the One-Time Setup (see

Section 5.2)

• The area setting of a Sub-Zone can be later updated through the

‘Area’ menu of the Basic Settings (see Section 6.4.1)

• The distance to Sub-Zone’s entry point can be update later

through menu P023

A1/A2/A3/

100

P023

Update Distance

To Sub-Zone

• This menu is shown only if a Sub-Zone has been dened.

• It allows to update the distance to Sub-Zone’s entry point.

• Scroll to choose the required Sub-Zone (A1/A2/A3/A4) and press

OK to update the distance to the entry point.

P024

SmartMow

(Default = OFF)

• SmartMow feature allows more efcient mowing operation

through the smooth and continuous turns when reaching lawn’s

edge.

• When this feature is enabled for the rst time in a particular

zone, it may require the mower to cross the lawn and “touch”

the perimeter wire several times (to perform an initial calibration

of the algorithm), before it will start performing smooth turns at

lawn’s edge.

• If there is more than one zone dened, then there is an option

to enable this feature for a particular zone or for the entire lawn

(‘All’).

• Please note! This feature may not be equally efcient on all lawns

or on different sections of a particular lawn, especially if a lawn

area is small or has narrow areas, big islands or slopes.

All

/L2/L3

/A2/A3/

/OFF

P025

SmartMow

Edge Overlap

(Default = 10)

• Allows adjusting the degree of overlapping with lawn’s edge,

when performing the smooth and continuous turns in SmartMow

mode.

• Increasing this value will cause a higher overlapping with lawn’s

edge (for better mowing results), but at some point may prevent

the mower from performing a smooth turn.

• If there is more than one zone dened, this setting may be set per

zone or for the entire lawn (‘All’).

5-30

P026

TurboMow

(Default = OFF)

• TurboMow feature allows faster and stronger mowing of a high

grass during the rst cut of the season.

• When a mower is operated for the rst time, or if the Factory

Defaults (“Out of the Box” settings - see Section 5.2) are invoked,

this feature is automatically set to ON to provide better mowing

results already after the initial mowing cycle. At the end of the

initial mowing cycle, the feature will be automatically disabled (set

to OFF).

• This menu allows to activate TurboMow feature manually. ‘U094’

(“Raise mowing height when activating the TurboMow mode.”)

will be displayed. At the end of the cycle the feature will be

automatically deactivated (set to OFF).

• When the TurboMow feature is activated, the initial mowing cycle

will be longer and noisier than the next mowing cycles.

On/OFF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow MC1200 - 2016 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow MC1200 - 2016

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info