Bedienungsanleitung Robomow MC1200 - 2016 (Seite 48 von 58) (Englisch)

644655

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Display Message / Descripon Required Acon

U089

Child Lock feature is activated.

The operational buttons are locked to prevent

unintended operation, especially by children.

To operate the mower, rst press one of the

operating mode buttons and then to press the

OK button to conrm.

U090-

U093

Sub-Zone 1/2/3/4 entry problem.

The mower eitherfails to leave/bypassthe Base

Station on its way to the Sub-Zone,orfails to enter

the Sub-Zone.

The mower will try to reach the Sub-Zone every

two hours. If the mower fails to reach the Sub-

Zone within threeattempts, it will stay in the Base

Station until the end of current mowing cycle.

The mower will not skip to the next Sub-Zone (if

there are any), if it fails to reach the current one.

Try to startmanual mowing (refer to section

6.3 – Manual Operation). Check if something

disturbs mower’s driving backwards and/or

bypassing the Base Station. Conrm the mower

drives along the perimeter wire and doesn’t fall

off the lawn’s edge, when it departs from the

Base Station.

Conrm that the mower is able to follow the

perimeter wire along the narrow pass untilit

reaches the Sub-Zone. Refer to section 4.3.3

for instructions on how to set a narrow pass

properly.

U094

Raise mowing height when activating the

TurboMow mode.

Refer to sections 5.1 and P026 in Section 6.4.2

in the User Manual.

9.4 Basic Troubleshoong

The next table will give details and possible causes of other faults, which do not provide error codes. If a fault

cannot be dealt with using these tables, please call your service provider.

Problem

Encountered

Probable Cause/Event Correcve Acons

Poor quality of

mowing

- Dull blade - Replace blade.

- The grass is too high in relation to the set

cutting height.

- It is recommended to cut less than a 1/3 of the

green part of the grass.

- Set the cutting height to a higher position and

then successively lower.

- If it is during a fast growing season – change

the Mowing Frequency (refer to Section 6.4.2 –

P001).

- The grass is wet and causes

accumulation of grass clippings around

the blade.

- For best cut, operate Robomow when the grass

is dry. Do no to mow in the early morning hours.

- Switch Off the Safety Switch and use heavy

gloves to clean and remove the grass clippings.

Mower doesn’t

nd the Base

Station

- There is a Perimeter Island or a Narrow

Passage that prevents the mower to

complete its drive towards the Base

Station in Near Wire Follow mode.

- Reduce the Near Wire Follow Distance in the

Settings menu from the default 7.

Mower doesn’t

depart from the

Base Station for

a long time

- There are several possible reasons for a

non-departure, including inactive times,

rain detection, etc.

- Press and hold ‘Home’ button for 1 second

while the mower is in the Base Station. The

non-depart reason code will be displayed for

3 seconds. Refer to Section 9.4.1 for detailed

description of no-depart codes.

Robomow

is noisy and

vibrates

- Damaged or unbalanced blade

- Check if the lawn is free from branches, stones

or other objects that can damage the blade.

- Replace the blade

Mower does not

dock properly

and sometimes

misses the Base

Station contacts

- Height differences between the lawn and

the Base Station surface.

- Fill some ground to atten the lawn to the Base

Station to allow smooth entrance.

- The wire underneath the Base Station is

not tight and placed in the middle of the

Station.

- Conrm the wire underneath the Base Station

is straight, tight, and centered below the Base

Station.

- The Base Station is set up on a side

slope.

- Move the Base Station to a relatively level

ground.

- The Base Station is placed too close to

the corner of the lawn

- Move the Base Station so it is not within 3

meters after a corner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow MC1200 - 2016 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow MC1200 - 2016

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info