Bedienungsanleitung Robomow RC302 (Seite 39 von 50) (Englisch)

537218

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

9.2 Detailed Error Codes

If the above table (Section 9.1) does not give enough information to help solve the problem, then press the

RIGHT arrow while the error code is displayed in order to receive a number that gives more details about the

problem and refer to the table below:

Display Message Probable Cause/Event Correcve Acons

0010

Mow

Overheat

- The mowing motor has been working

under a severe load for too long.

- No need for action – Robomow will renew

automatically the operation after the

mowing motor will cool down.

0011

Drive

Overheat

- The drive motors have been working under

a severe load for too long.

- No need to do anything.

- Robomow will renew the operation

automatically as soon as the drive motor

will cool down.

0012

No wire signal - See E3 in the above table

0014

Front wheel

problem

- See E7 in the above table

0015

Button

pressed

- One of the operating panel buttons is

constantly pressed.

- Press ‘OK’ to conrm the message and

continue operation. This message is

displayed to inform only.

0016

Low

temperature

- Mower does not depart automatically

from the Base Station when the ambiance

temperature is lower than 5ºC (41ºF).

- Information - When the temperature is

below 5ºC (41ºF) the grass does not grow

or grows very slowly.

However Manual Depart is enabled.

- No need to do anything.

- Robomow will renew the operation

automatically as soon as the ambiance

temperature will rise above 5ºC (41ºF).

0020

Rain detected

- The operation is delayed as Robomow

detects rain.

- No need for action.

- The message is displayed until Robomow

will not detect rain and then will start

mowing.

Display Message Probable Cause/Event Correcve Acons

E 6

Check Drive

- Grass or other object has wrapped

around the drive wheel.

- The drive motors have been

working under severe load for too

long.

- Check the drive wheels and remove the

grass or other objects.

E 7

Front Wheel

Problem

- The Front Wheel has left the

ground for too long during

operation.

- If Robomow has driven onto an obstacle,

Switch off the Safety Switch, raising the front

end: Remove or exclude the object from the

mowing area.

- If Robomow is being used on a slope too

steep for safe mowing, exclude this from the

mowing area.

- If high grass is preventing the front wheel

from fully turning on the ground, raise the

cutting height.

- If the ground contains large holes or

indentations where the front wheel can drop

into when passing across, ll these areas

with dirt and level off.

E 8

Decrease

Inactive Time

- Too many Inactive Days and/or

Hours have been set for your lawn

area.

- Decrease the number of Inactive Days and/

or the number of Inactive Hours to allow

Robomow to complete mowing your lawn.

E 9

See

Troubleshooting

in Manual

- E 9 is displayed for all other

messages that are not listed in the

above table.

- Press the ‘Right arrow’ button to receive the

stop reason number and refer to the next

table for more details about the stop reason,

causes, and actions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow RC302 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow RC302

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info