Bedienungsanleitung Robomow RC304 - 2016 (Seite 34 von 58) (Englisch)

644650

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Chapter 6 –

Robomow Operation

6.1 Automac Operaon

o Once the One-Time Setup is nished, Robomow will be set to perform automatically the following cycle of

mowing operations:

- When the battery is fully charged, Robomow will automatically depart from the Base Station.

- It will mow the lawn.

- It will start searching for the Base Station, when the battery level gets low (Robomow will not mow when

it is searching for the Base Station).

- It will recharge the battery and get ready for the next scheduled operation.

- It will continue mowing until it completes the required number of mowing hours (end of a Mowing Cycle).

Note: Robomow mows the Edge of the entire lawn only on the rst mowing operation of each Mowing Cycle.

In the rest of operations Robomow mows the lawn without the Edge. When Mowing Frequency (p001 in

Section 6.4.2) is set to HIGH, Robomow will mow the Edge twice a week.

o The required mowing time for a single mowing cycle is automatically derived from the Area setting for your

lawn.

o In case the required mowing time within a mowing cycle needs to be adjusted (increased/decreased) to

achieve better mowing results, it can be done using the Mowing Hours menu – see Section 6.4.2.

o Robomow usually performs several consecutive mowing operations until it completes a full mowing cycle

required for the lawn. After completing a mowing cycle Robomow will rest until the next cycle should begin.

The interval between mowing cycles is dened by the Mowing Frequency menu – see Section 6.4.2. The

default setting is to perform two complete mowing cycles per week (Medium Mowing Frequency)

o Robomow stays in the Base Station during the default Inactive Time (All day Sunday and nighttime daily

23:00 to 06:00). Inactive Time may be changed – see Section 6.4.1.3.

Note!

Robomow has the power to mow high grass. However when mowing high grass during the rst use or the rst

mowing of the season, initially you will see uneven patches of grass.

Please be patient as it may take a few days to one week to overcome and bring the lawn to an even height and

consistency.

6.2 Operang Panel

Operating Panel and buttons:

Tu We Th Fr Sa Su

Days of the week

Mower is in the

Base Staon

indicator

Day and Time

seng indicator

Mowing Hours (%)

seng indicator

Inacve Time

seng indicator

Rain Sensor

Red lit constantly – Low Baery

Green blinking – Charging

Green lit constantly – Fully Charged

Baery and

Charging

indicator

User / Error messages

Area seng indicator

STOP

Mowing with Edge / Le

arrow

OK to choose /

approve selecon

Mowing without Edge /

Right arrow

GO to Base (Home)

Stop (during operaon) /

Back while in the menu

Sengs

6.3 Manual Operaon

Manual Operation is used when you want to manually send the mower to mow your lawn, regardless the

Automatic Operation’s schedule.

To initiate Manual Operation, while Robomow is at the Base Station, press one of the buttons (except the STOP

button) to show the display.

If the battery is fully charged and the Automatic Operation is enabled (see Section 7.3), then the start time of the

next operation is displayed, otherwise the current day and time are displayed.

Once the display is shown, choose the operation mode you want as provided in the table below:

Operation Mode Child Lock is Off Child Lock is On

Mowing with Edge – Mowing

the edge of the entire lawn before

starting to mow the inner area of

a selected zone.

It is recommended to use this

mode once or twice a week,

depending on how fast the grass

is growing.

Press the ‘Edge before mowing’

(left arrow) button once

Press the ‘Edge before mowing’

(left arrow) button then press OK

Mowing without Edge – Mowing

only the inner area of a selected

zone without the edge.

It is recommended to use this

mode only in the rst operation of

each Mowing Cycle.

Press the ‘Mowing’ (right arrow)

button once

Press the ‘Mowing’ (right

arrow) button then press OK

Note – if a Sub-Zone is dened, L1 (Main Zone) will be displayed when you choose an operating mode. Use the

arrow buttons to scroll and choose the required zone to be mowed and press OK.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow RC304 - 2016 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow RC304 - 2016

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info