Bedienungsanleitung Robomow RC308u (Seite 40 von 58) (Englisch)

664045

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Screen Seng Descripon Opons

P025

SmartMow

Edge Overlap

(Default =

10)

• Allows adjusting the degree of overlapping with lawn’s edge,

when performing the smooth and continuous turns in SmartMow

mode.

• Increasing this value will cause a higher overlapping with lawn’s

edge (for better mowing results), but at some point may prevent

the mower from performing a smooth turn.

• Ifthereismorethanonezonedened,thissettingmaybesetper

zone or for the entire lawn (‘All’).

5-30

P026

TurboMow

(Default = OFF)

• TurboMow feature allows faster and stronger mowing of a high

grassduringtherstcutoftheseason.

• When a mower is operated for the rst time, or if the Factory

Defaults (“Out of the Box” settings – see Section 5.2) are invoked,

this feature is automatically set to ON to provide better mowing

results already after the initial mowing cycle. At the end of the

initial mowing cycle, the feature will be automatically disabled (set

to OFF).

• This menu allows to activate TurboMow feature manually. ‘U094’

(“Raise mowing height when activating the TurboMow mode.”)

will be displayed. At the end of the cycle the feature will be

automatically deactivated (set to OFF).

• When the TurboMow feature is activated, the initial mowing cycle

will be longer and noisier than the next mowing cycles.

On/OFF

P027

RoboHome

(Default = OFF for

all models except

‘RC312 Pro S’)

• Allows proper rain detection when RoboHome accessory is

installed.

• When set to ON, Robomow will drive back from the Base Station

to sense the rain before beginning an operation. If rainy conditions

are sensed, Robomow will drive back to the Base Station and

postpone the operation.

On/OFF

P028

External Base

(Default = OFF)

• In case the Base Station is installed outside the perimeter of your

lawn (“External Setup”, see section 3.2.3), this option sets the

distance (in meters) from the Base Station that your Robomow

needs to drive before starting to mow your lawn.

OFF/1/2/

3/4/5

6.4.3 Robomow App Settings

Using the Robomow App you will have access to additional menu options that are not available on the mower,

such as an option to set an additional window of Inactive Hours.

6.5 Operaon in a Non-Base Zone (using a Perimeter Switch)

In order for Robomow to operate in a Non-Base Zone, the Perimeter Switch has to be turned on and the mower

should be inside the active perimeter area.

• Verify that the Perimeter Switch is connected to the zone to be mowed.

• Press the ‘ON’ button to turn on the Perimeter Switch.

• Drive/carry Robomow to the lawn area. Refer to “Transportation” part of Section 1.3 for carrying instructions.

• To initiate the operation, choose the operation mode you want, press the arrow buttons to choose the Zone

you want to mow and press OK to start operation (refer to Section 6.3).

• When Robomow completes the mowing, it will stay on the lawn. You will have to drive/carry it back to its place

for charging.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow RC308u Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow RC308u

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info