Bedienungsanleitung Robomow RC308u (Seite 44 von 58) (Englisch)

664045

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Display Message Probable Cause/Event Correcve Acons

No Wire Signal

- Power Box/Perimeter Switch is not

turned on or not connected

- Power Box may need to be

restarted

- The Perimeter Wire is not

connected to the Base Station/

Perimeter Switch.

- The Perimeter Wire is cut.

- Make sure the Base Station is connected to

the mains supply.

- Disconnect the Power Box from the mains

power and reconnect after 10 seconds.

- Check that the low voltage cable between

the Power Box and the Base Station is

connected.

- Check the LED indications on the Power

Box.

- Check the connection of the Perimeter Wire

to the Base Station / Perimeter Switch.

- Check the installation for cut wire. Repair

broken cable with the waterproofed

connector supplied in the box.

Check Power

- Power Box is not plugged in

properly into the power outlet.

- No power at the power outlet or

the main power is shut off.

- The mower or Base Station

contacts are dirty.

- Charging is not detected, although

there is a physical contact between

the mower and the Base Station

contacts.

- ConrmPowerBox is plugged into the

power outlet.

- Turn power on to the power outlet.

- Check the power outlet using another

appliance.

- Clean the contacts with a brush or piece of

cloth.

- ConrmagoodconnectionofthePower

Box to the Base Station.

Check Blade /

Cutting Height

- Mowing motor has faced over-

current conditions for too long as a

result of high grass or an obstacle

that is stuck or wrapped around

the blade.

- Something is preventing a blade

from rotating freely (Accumulated

grass clippings under the mowing

deck; rope or similar object

wrapped around mowing blade).

- CAUTION – Switch off the Safety Switch

before checking the blade.

- Inspect blade for foreign material or debris

preventing rotation.

- Clean out accumulated grass clippings using

a wooden stick.

Check Drive

- Grass or other object has wrapped

around the drive wheel.

- The drive motors have been

working under severe load for too

long.

- Check the drive wheels and remove the

grass or other objects.

Front Wheel

Problem

- The Front Wheel has left the

ground for too long during

operation.

- If Robomow has driven onto an obstacle,

Switch off the Safety Switch, raising the front

end: Remove or exclude the object from the

mowing area.

- If Robomow is being used on a slope too

steep for safe mowing, exclude this from the

mowing area.

- If high grass is preventing the front wheel

from fully turning on the ground, raise the

cutting height.

- If the ground contains large holes or

indentations where the front wheel can drop

intowhenpassingacross,lltheseareas

with soil and level off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow RC308u Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow RC308u

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info