Bedienungsanleitung Robomow RC312u (Seite 39 von 58) (Englisch)

664046

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Screen Seng Descripon Opons

P019

Bluetooth Remote

Control Pairing

• Enables the pairing process between your Robomow and

an outdoor Bluetooth Remote Control that is available as an

accessory (Refer to Paragraph 12 Accessories).

P020

Last Termination

Event

• Enables the Behavior View of the special display (may be required

by a Service Station)

P021

Program On/Off

(Default = ON)

• This menu enables or disables (pauses) Automatic Operation

either in the main zone (‘L1’), one of the Sub-Zones (‘A1/ A2/ A3/

A4’) or in the entire lawn (‘All’).

• This menu is only relevant when the Automatic operation is

enabled on the Power Box (see chapter 7.3)

• When Program is set to Off in a particular zone, the mower will

skip the operation in that zone, but will continue to mow all the

other zones.

• Note! If Program is set to ON at least in one zone, the mower will

continue to mow the edge of the entire lawn at the beginning of

each mowing cycle, as described in Section 6.1.

All

/A2/A3/

/OFF

P022

Add Sub-Zone

• Enables the addition of a Sub-Zone. Maximal number of Sub-

Zones may be different for each Robomow model.

• A1/A2/A3/A4(nameoftherstavailablesub-zone)isdisplayed

– press OK.

• If the mower is not at the Base Station, then ‘U044’ (“Place the

mower in the Base Station”) is displayed. Place the mower in the

Base Station and press OK.

• The mower will start moving towards the Sub-Zone.

• Scroll to set the area of the Sub-Zone and press OK.

• Note! This process is not a part of the One-Time Setup (see

Section 5.2)

• The area setting of a Sub-Zone can be later updated through the

‘Area’ menu of the Basic Settings (see Section 6.4.1)

• The distance to Sub-Zone’s entry point can be update later

through menu P023

A1/A2/A3/

100

P023

Update Distance

To Sub-Zone

• ThismenuisshownonlyifaSub-Zonehasbeendened.

• It allows to update the distance to Sub-Zone’s entry point.

• Scroll to choose the required Sub-Zone (A1/A2/A3/A4) and press

OK to update the distance to the entry point.

P024

SmartMow

(Default = OFF)

• SmartMow feature allows more efcient mowing operation

through the smooth and continuous turns when reaching lawn’s

edge.

• When this feature is enabled for the rst time in a particular

zone, it may require the mower to cross the lawn and “touch”

the perimeter wire several times (to perform an initial calibration

of the algorithm), before it will start performing smooth turns at

lawn’s edge.

• If there is more thanonezone dened, then there isan option

to enable this feature for a particular zone or for the entire lawn

(‘All’).

• Please note! Thisfeaturemaynotbeequallyefcientonalllawns

or on different sections of a particular lawn, especially if a lawn

area is small or has narrow areas, big islands or slopes.

All

/L2/L3

/A2/A3/

/OFF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow RC312u Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow RC312u

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info