Bedienungsanleitung Robomow RL555 (Seite 69 von 84) (Englisch)

512480

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Chapter 8-7

Troubleshooting

Problem Encountered Probable Cause/Event Corrective/User Action

Operation

Robomow will not operate and

nothing will display on the LCD

screen.

- Mower is in deep sleep.

- If not connected to the charger at all times when

not in use, the Robomow will conserve power by

entering into a deep sleep mode. Lift Power Pack

from mower and re-insert it after 10 seconds.

- Power Pack has been discharged from

lack of charge maintenance.

- It is required for the charger to remain connected

to the Robomow when not in use. Failure to do

so can cause permanent Power Pack damage.

Contact your service provider.

Robomow drives but blades will

not mow.

- ‘Mowing’ has been turned to off. - Change back on under ‘User Preferences’

Short run time, operates less

time than normal.

- Power Pack is not fully charged

- Connect the charger to the mower and keep it

connected until the ‘Ready – Keep Charging’

message displays in the LCD screen.

- ‘Work Time ‘ for that zone is set to stop at

a pre-determined duration.

- Work time can be changed under ‘User

Preferences’

- Grass is extremely over grown or very

wet.

- Raise cutting height. Always mow the grass

frequently enough to prevent over growth. Refrain

from cutting wet grass.

- Power Pack is reaching a normal end of

life state.

- Replace Power Pack. Properly maintain Power

Pack per instructions.

- Manual Controller is not firmly pivoted

down flush in holder, allowing it to bounce

up and stop the mower.

- Confirm the coiled cord is fully placed into the

holder below the Manual Controller and the Manual

Controller closes flush with the top of the mower.

Robomow has crossed over

wire during operation

CAUTION The Robomow is

designed to remain within an

active perimeter of your lawn

when properly installed. In

the unlikely event that the

mower does cross over the

wire, DO NOT use the mower

until the problem is corrected.

If changing the perimeter wire

placement does not correct this

problem, contact you service

provider.

- Improper perimeter wire setup OR

adjacent zone (closer than 13 feet / 4 m)

operated simultaneously.

- Refer to the setup rules for wire placement,

particularly for corners. Do not operate adjacent

plots simultaneously when closer than 13 feet (4

m).

Robomow does not complete

the edge in a non-docking zone.

Peculiar geometry of perimeter Perform ‘Learn Edge’ (refer to 7.2.1 Chapter 7-4).

The Robomow gets stuck fre-

quently when traveling over less

than optimal terrain.

Low ground clearance. Raise ground clearance to the uppermost position.

Cutting height too low. Raise cutting height

Terrain needs landscaping repairs.

Fill in all holes, cover or exclude all exposed roots etc in

order to smooth the terrain.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow RL555 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow RL555

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info