Bedienungsanleitung Robomow RM200 (Seite 29 von 44) (Englisch)

512474

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Message

Displayed

Probable Cause/Event Corrective/User Action

Keys locked - Child lock feature has been activated

- Press the Up



arrow key and then

press the ‘STOP’ button.

Child lock can be deactivated under the

‘Settings’ menu.

Low temperature

waiting…

- Robomow is charged and the ambience

temperature is out of range (below 32ºF /

0ºC);

- Do not do anything, the charging is

stopped and Robomow is waiting for

temperature to change back to the

allowed range; if temperature stays out

of the range for more than 12 hours, the

message is changed to ‘Low temp.

Press GO’.

Mow overheat

cooling, wait…

- The mowing motor has been working under

a severe load for too long of a time.

- There is no need to do anything –

Robomow will renew automatically the

operation, as the mowing motor will

cool down.

No wire signal

- Perimeter Switch is not turned on or not

connected to the zone intended to mow.

- The perimeter wire is not connected to the

Perimeter Switch

- The perimeter wire is cut

- Make sure the Perimeter Switch is

connected to the mains supply

- Disconnect the power supply from the

mains power and reconnect after 10

seconds.

- Check the Perimeter Switch is

connected to the correct zone and is

turned on.

- Check the connection of the perimeter

wire to the Perimeter Switch.

- Check for cut in the perimeter wire.

Rain detected

GO to ignore

- Robomow detects rain upon GO pressing

(received when pressing the GO button)

- Do not operate Robomow in rainy

weather and wet grass; If you choose to

override, press the ‘GO’ button; The

overriding is valid for the current

operation only

Rain detected

Press GO

- Robomow has skipped the last depart due to

rain detection

- It is not recommended to cut wet or

damp grass, but if you choose to

override the rain sensor, change the

setting of the ‘Rain sensor’ to ‘off’ under

the ‘Settings’ menu.

Rain sensor

disconnected

- Disconnection in the rain sensor wires.

- Press ‘GO’ to confirm the message and

call service for repair.

Ready

keep charging

- The battery is fully charged

- Keep the charger (power supply)

connected and operating

Recharge battery

- The maximum operating time has been

reached

- Connect the charger to the mower

Remove fuse

before lifting

- Robomow was lifted while the battery fuse is

connected.

- Remove the fuse before lifting

Robomow.

Remove fuse then

check blade

- Some obstacle is stuck or wrapped around

the blade.

- Something is preventing a blade from

rotating freely. Severe grass accumulation

under the mowing deck; rope or similar

object wrapped around mowing blade.

- Object jammed under mower preventing

blade from rotating.

- CAUTION – Remove battery fuse

before lifting the mower.

- Inspect blades for foreign material or

debris preventing rotation.

- Clean out accumulated grass clippings

using a wooden stick.

Replace blade

every 200 hours

- An automatic reminder to replace the blade

is displayed every 200 hours

- Replace the blades and restart the

counter of the blades replacement

reminder by choosing the ‘Blades

replaced – Clear reminder’ option

under the ‘Settings’ menu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow RM200 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow RM200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info