664052
52
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
Robotic Mower
RX20 Pro, RX20u, RX12u
EN
User Guide
Original Operating Instructions
See
how to
Install
1/Learn
Your Lawn
I’m
Robomow,
nice to
meet you.
Your safety is important to us -
Please review this Manual carefully for all safety warnings and
take extra caution to keep both children and pets off the lawn
when Robomow is in operation.
Safety rst.....................
2
Installation...................
13
Quick reference..............
35
3
Warning
decal denitions
1. This is a dangerous power tool. Exercise care when operating
and follow all safety instructions and warnings.
2. Read the Safety Manual carefully before operating your
Robomow.
3. Be careful of thrown objects during operation.
4. Keep a safe distance from Robomow while it is operating. Keep
people, especially children, pets and bystanders away from the
area where Robomow is operating.
5. CAUTION – Do not touch rotating blade. Keep hands and feet
away and do not lift Robomow from the ground.
6. Remove the disabling device before working on or lifting
Robomow (see Section 3.b).
7. Do not ride Robomow.
This symbol is normally found on plastic enclosures and
indicates that the mains electricity is double insulated
This symbol indicates that the product is designed for
indoor use only.
Do not dispose of Robomow or any of its parts as unsorted
municipal waste. It should be collected separately.
This product conforms to applicable EU directives.
1 2 3 4 5 6 7
4
A. Before you begin
1. Read this Safety Manual carefully before operating
Robomow to become familiar with its controls and
proper use.
2. Never allow children, persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge or people unfamiliar with these
instructions to use the machine. Local regulations
may restrict the age of the operator.
3. You are responsible for accidents or for harm to other
people or their property.
4. It is your responsibility to inform your neighbors about
the risks, and that it is forbidden to enter your lawn
while Robomow is operating.
5. If your lawn is open to the street and/or your neighbors,
you must be present during the mower’s operation to
prevent others from accessing your lawn. Alternatively,
you must protect / fence your lawn so that others will
not be able to access the mower during operation.
B. Preparations
1. Ensure the correct installation of the Perimeter Wire,
as instructed.
2. Inspect periodically the area where Robomow is used
and remove all stones, sticks, cones, wires and other
foreign objects.
3. Periodically visually inspect to verify that the blade is
not worn or damaged. Replace a worn or damaged
blade (Part No. MRK9100A). Switch Robomow off
when inspecting or replacing the blade.
Safety warnings &
precautions
5
C. Operation
IMPORTANT SAFETY WARNING!
Do not leave Robomow to operate unattended if you know
that there are pets, children or people in the vicinity.
Never mow while people (especially children) or pets are
nearby.
1. Do not operate Robomow if any safety feature or any part is
damaged, worn or inoperable.
2. Keep hands and feet away from the cutting blade and other
moving parts.
3. Always switch Robomow off before lifting it or planning to
operate any adjustments.
4. Never pick up or carry Robomow while the motors are running.
5. Do not touch the blade before it has completely stopped
rotating.
6. Do not use Robomow for any purpose other than cutting lawn.
7. Keep all guards, shields, safety devices, and sensors in place.
Repair or replace damaged parts, including decals.
8. Set the weekly program at times when there are no people on
the grass.
9. Do not connect a damaged power cord to the supply, or touch
a damaged cord before it is disconnected from the supply as it
can lead to contact with live parts.
10. Keep the extension power cord away from the blade to prevent
Robomow from damaging it. A damaged power cord can lead
to contact with live parts.
11. If the power cord becomes damaged or entangled during use,
detach it from the mains by pulling the plug from the socket.
12. In the event of accident or breakdown whilst Robomow is
operating, immediately press the red STOP button.
6
IMPORTANT! It is recommended to keep the original
packaging for shipping purposes.
D. Transportation
Within the working area:
1. Press the STOP button to stop
Robomow.
2. Switch Robomow off, and carry
it by its carrying handle as
shown in the picture to the right.
Over long distances:
When transporting Robomow
over long distances, make sure it
is switched off.
7
E. Using the remote control (manual mowing)
1. Mow only in daylight or in good artificial light, and avoid
operating on wet grass.
2. Do not operate Robomow barefoot or wearing open sandals.
Always wear substantial footwear and long trousers; always
make sure of your footing on slopes.
3. Use extreme caution when reversing the direction of the
mower towards you.
4. Always switch on the motor according to the instructions while
standing away from the blade.
5. Do not mow manually in slopes greater than 15 degrees or
where a firm footing is not possible.
F. Batteries
1. Do not open or damage the battery pack.
2. The Battery Pack contains electrolytes. In case of an electrolyte
leakage from the Battery Pack, the following actions should be
taken:
Skin contact: Wash the contact areas off immediately with
water and soap.
Eye contact: Flush the eyes with plenty of clean water for at
least 15 minutes immediately, without rubbing.
Get medical assistance.
3. Ensure that the battery is charged using the correct charger
recommended by the manufacturer. Incorrect use may result
in electric shock, overheating or leakage of corrosive liquid
from the battery.
8
G. Maintenance and special instructions
1. Always switch Robomow off and remove the Disabling
Device before clearing blockage/checking/cleaning/
working on it, or after striking a foreign object to inspect
the machine for damage. Never attempt to service or
adjust the mower while it is in operation.
2. In case of abnormal vibrations, stop the mower, switch
it off and check for any damage of the blade. Replace
a worn or damaged blade (Part No. MRK9100A) to
preserve balance. If the vibration continues, call for
service.
3. Use heavy gloves when inspecting or servicing the blade.
4. Do not perform maintenance barefoot or wearing open
sandals. Always wear suitable work shoes and long
trousers.
5. Replace worn or damaged parts for your safety.
6. Use only original equipment and accessories. It is not
permitted to modify the original design of Robomow. All
modifications are made at your own risk.
7. Ensure that only replacement cutting means of the right
type (Part No. MRK9100A) are used.
8. Maintenance/servicing/cleaning of Robomow should be
according to manufacturer’s instructions.
9. Keep all nuts, bolts and screws tight to be sure the
machine is in safe working condition.
WARNING!
When there is a risk of a lightning storm, disconnect
the Perimeter Wire from the Base Station and the
Power Supply 230 V/120 V plug from the power outlet.
9
H. Product end of use
1. Robomow and its accessories should be collected separately
at the end of their life to prevent waste electrical and electronic
equipment from ending up in landfill sites, and to protect and
improve the quality of the environment.
2. Do not dispose of Robomow or any other of its parts (including
the Power Supply and Base Station) as unsorted municipal
waste – they should be collected separately.
3. Ask your local distributor/dealer about return and collection
systems availability.
4. Do not dispose of the battery pack in a fire, and do not place
used batteries in your household trash.
5. The battery must be collected, recycled, or disposed of in an
environmentally sound manner.
10
Robomow safety
features
WARNING!
Robomow is equipped with numerous built-in
safety features. However, the mower is a hazardous
device with a sharp blade, which can cause major
injury to anyone who comes in contact with it.
Therefore, it is absolutely forbidden to be on the lawn
while the mower is working. Alternatively, halt the
mower’s operation when people (especially children)
or pets are to stay or play on the lawn.
A. Child Lock
The Child Lock prevents unintended operation of
Robomow by an accidental press of one of the buttons.
Only pressing two buttons in the right order will initiate
the operation. It is required to activate the Child Lock
feature if children under age 6 may come in contact
with Robomow.
B. Disabling Device
The Disabling Device will prevent anyone from
operating Robomow when it is removed. It is highly
recommended to remove the Disabling Device to
prevent operation of the mower by children or people
who are unfamiliar with Robomow or are not allowed
to use it.
C. Lift Sensor
If the mower is raised from the ground during
the blade’s operation, the blade will stop rotating
immediately.
11
D. Tilt Sensor
If the mower is tilted up towards a vertical position, the blade
will stop immediately.
E. Obstruction Sensor
Robomow detects interfering obstacles in its way during
operation. When the mower collides with an obstacle, it will
stop the rotation of the blade immediately, will stop movement
in that direction and reverse itself away from the obstacle.
F. Emergency Stop Button
Pressing the STOP button at any time during operation will
stop the mower and the blade immediately.
G. GO/ON-OFF button
The GO/ON-OFF button allows to completely power off your
Robomow. Switching Robomow off will prevent it from any
operation. It is required to switch Robomow off before lifting it and
before any maintenance operation.
H. Base Station and Perimeter Wire
Robomow cannot operate without a Perimeter Wire installed
and activated through the Base Station. In the event the
Perimeter Wire signal is turned off, Robomow will stop
operating.
I. Anti-Theft (RX20u/RX20 Pro models only)
The theft protection function will prevent anyone from using or
driving Robomow unless they unlock it by connecting to it with
a registered mobile device.
12
Let’s get
started.
Can’t wait
to mow your
lawn
13
Installation
Congratulations on purchasing Robomow! You are just a few steps
away from meeting your best team player. Very soon you will come to
count on your Robomow to do a perfect job.
A preinstalled Perimeter Wire will set the boundaries (a “virtual wall”)
for your Robomow. The Perimeter Wire will be laid around the edges
of your lawn and objects that you want to protect.
Robomow will move randomly within its working area, as defined
by the Perimeter Wire. This kind of random movement provides the
perfect cut and ensures complete coverage of your lawn. At the end
of each mowing ride, Robomow will automatically return to base for
charging.
After a quick and simple installation, you will be ready to enjoy your
free time while Robomow looks after your lawn.
14
So where are we heading?
Get started
Choose Base Station location
Lay the wire
Wire your lawn
Power up
Connect Everything
GO!
Your Robomow is ready
Set base
Install the Base Station
Correct installation of your Robomow will ensure maximum results.
This is what it takes to prepare your Robomow to do a perfect job for
you.
15
This is what you nd
in the box
Power Supply
With 10 m / 33 ft extension cable
Base Station
This is where Robomow recharges
Perimeter Wire with a plot
connector* 80 m / 260 ft
(70 m / 230 ft for RX12u)
Marks the working area for
Robomow
(*) Not provided with RX20 Pro model
Wire Pegs* 150 pcs.
(100 pcs. for RX12u)
For securing the wire to the ground
(*) Not provided with RX20 Pro model
Base Station Head
Generates Perimeter Wire signal
Robomow RX model
Your new Robotic Mower
RoboTool
For blades replacement and
servicing. IMPORTANT! Keep this
tool for future use.
16
Ready? Let’s begin...
Plot Connectors [X2]
For connecting the Perimeter
Wire to the Base Station
Wire Connectors [X2]
For splicing the Perimeter
Wire in case of a cut
RoboRuler
For measuring the Perimeter Wire’s
distance from the lawn’s edge
Base Station Stakes (x4)
For fixing the Base Station to the
ground
Printed Instruction Material
Manual
17
The Base Station is where Robomow recharges, and where the
Perimeter Wire starts and ends. In this installation step, you are going
to determine a proper location for the Base Station.
Prefer a corner installation
Get started
** See additional installation options in Appendix A **
Choosing the Base Station location
Min 1 m / 3.3 ft
18
TIP
The Base Station will be installed at a later stage, after the
Perimeter Wire is in place.
A minimum of 1 meter / 3.3 feet
from a sprinkler head to avoid
damaging the mower’s internal
components
Even and flat (up to +/-5% slope)
A min. of 1 meter / 3.3 feet
straight wire before the base
to allow smooth docking
Up to 10 meters / 33 feet away
from a power outlet
Base Station
Max 10 m / 33 ft
Follow these simple guidelines to nd a proper location for
your Base Station
Min 1m /3.3ft
19
Lay the Perimeter Wire (“virtual boundary”),
which defines the working area for Robomow
Lay the
wire
Have your Robomow box nearby.
Be sure to cut your grass with your old mower one last time
before you start wiring. This will make inserting pegs easier
and help ensure Robomow doesn’t cut the wire.
Combination pliers
TIPS
A. Make a good start
WHAT
YOU’LL
NEED
Cutter
Use the RoboRuler to determine a distance, which you should keep
between the Perimeter Wire and the lawn’s edge.
Hammer
20 cm/8”
20
Pull out the wire marked
A from the Perimeter
Wire spool; leave a tail of
approx. 20 cm / 8”; once a
tail is made, put the first
peg into the ground to
secure this wire end.
Drive pegs at two
additional locations: at
RoboRuler distance I
along the edge from the
first peg, and at RoboRuler
distance III from the edge
as shown in the picture.
2
3
Measure RoboRuler distance
III from the corner, where
you intend to install the
Base Station and mark
this point on the ground.
1
21
TIP
If your lawn has a corner with a relatively flat edge, you can move the
beginning of the wire up to 60 cm / 2 ft outside the lawn.
This will define how far off the lawn the Base Station will be
installed.
Well done! This was the most complex part
of the wire installation. Let’s move on…
22
Lay the Perimeter Wire loosely along the perimeter as you walk along
the lawn’s edge.
Use the RoboRuler to determine the distance, which you should keep
between the Perimeter Wire and lawn’s edge.
B. Keep proper distances
Start unwinding the wire counter-clockwise around the lawn
starting at the Base Station’s location.
When the edge is a wall, use also
distance III of the RoboRuler.
If the edge is a drop, use
distance III of the RoboRuler.
If the edge is relatively flat,
lay the wire at RoboRuler
distance II from it.
23
The Perimeter Wire is secured to
the ground by the pegs supplied
with Robomow.
Pull the wire tight while
hammering the pegs to their
final depth in the ground.
Take care not to damage
irrigation pipes.
Place the pegs every few tens of
centimeters.
Add pegs where necessary to keep
the wire tight to the ground to
avoid damaging it by Robomow.
Leave a minimum of 1.2 m (4 ft) if the edge of the lawn borders water.
Min 1.2m (4ft)
25
E. Complete wire setup
Arrive back to the base location until the two wire ends meet each other
Make sure to keep at least 1.5 meters / 5 feet of a straight wire at the very end
Put the last peg very close to the first one
26
Put one of the provided plot connectors on the second wire end
Use pliers to press the connector and a cutter to cut off the
remaining wire
Make both wire end the same length
Do not leave or create wire wraps
a
b
c
27
Set base
3
Place the Base Station in its planned location
Align it to the lawn’s edge
Use RoboRuler distance I to confirm that the center of the Base Station
is properly shifted right relative to the wire, as shown in the picture
Fix the base to the ground with the 4 supplied metal stakes
Be careful not to damage irrigtion pipes when hammering
down the stakes.
28
Power
up
1. Connect the wire tail marked A to the A terminal and the other tail
to the B terminal of the Base Station head.
2. Connect the power supply connector to the Base Station head as well.
3. Note the markings for placing the Base Station Head.
Markings for placing the Base Station Head
29
4. Place the head on the Base Station and align it with the markings as
shown in the picture below.
5. Slide the head all the way through.
Pay attention to the sliders and a dedicated slot for threading the wires.
Slide
30
6. Plug in the power supply into a socket.
TIP
If for some reason you need to remove the base station head,
you can do so by lifting the lever (A) and pushing it towards the
inside of the base.
Take the power cord out of the mowing area (to prevent
Robomow from damaging it) and secure the cord firmly to
the ground (so that it does not become a tripping hazard).
31
GO!
Your Robomow is ready!
Place Robomow in the center of your lawn
Press GO for 2 seconds to switch it on
Now press the STOP /
once to send Robomow to the Base Station.
Robomow will start driving* towards the edge of the lawn to locate
the Perimeter Wire. Once on it, Robomow will follow the wire to
reach the Base Station and park there for charging.
(*) If Robomow doesn’t start driving, but plays a long beep and blinks with
ON-OFF indication in red, you should swap the Perimeter Wire connection
at the Base Station Head. For additional troubleshooting information please
refer to “Troubleshooting” section in the “Quick reference” part.
2 sec
32
Appendix A
Additional installation options
1. On-wire with a flat edge.
2. On-wire with a drop edge.
0 cm
33
Appendix B – Secondary areas
Connected secondary areas
If your lawn has additional areas connected
with a passage and Robomow is able to drive
through it, then you should bear in mind the
following rules:
Separated secondary areas
If your lawn has areas, that are completely
separated (by a fence, sidewalk, pathway, etc.),
then you can extend the perimeter wire to
cover such secondary areas as shown in the
picture below.
• The minimal distance between the wires in such passage
should be 15 cm / 6”
• The minimal width of such passage should be 57 cm / 22”
Min 15 cm
Min 57 cm
Quick reference
Knowing your Robomow
Single-button operation
Additional options with the mobile app
Taking care of your Robomow
Troubleshooting
FAQs
How to get service
Specications
Warranty card
35
37
Bottom view
Floating
Mowing Deck
Rugged drive
wheels
Mowing Blade
Lift sensor
38
Operating panel
STOP / Home
button
Lock indication:
Steady orange: child
protection is active
Blinking orange: theft
protection is active
ON-OFF indication:
Steady green: mower is switched
on / mower is in operation
Blinking green: mower is returning
to the Base Station / mower is
driving to a starting point
Blinking green fast (and beeping):
mower is departing from Base
Station
Blinking green slow: mower is
asleep
Blinking red / steady red: mower
is at fault (see troubleshooting
section)
GO /
ON-OFF switch
Battery indication:
Blinking green: mower is
charging in the base
Steady green: the battery is
fully charged
Blinking red: the battery is
almost empty, recharging will
soon be required
Steady red: the battery is low
and needs to be recharged to
resume operation
39
Charging pins
Base Station head
Rear slot and
opening for
head’s removal
Base Station Indication:
Steady green: perimeter wire signal is OK; the mower
is inside the base
Blinking green: perimeter wire signal is OK; the
mower is outside the base
Blinking red fast: perimeter wire is damaged or
disconnected
Blinking red slow: poor perimeter wire connection or
the wire is too long
Steady red: faulty power supply
Base Station
40
Before anything else
Single-button
operation
Clean the lawn from stones, fallen branches or other foreign objects
before using Robomow.
Set the mowing height to the desired level. We recommend setting
the mowing height to the maximum during the first mowing operation
or at the beginning of a season, and then gradually reducing it to the
desired level.
To set the mowing height, push and turn the mowing height
adjustment knob to the desired direction:
I means the lowest mowing height
IIII means the highest mowing height
IMPORTANT SAFETY WARNING!
Do not leave Robomow to operate unattended if you know
that there are pets, children or people in the vicinity.
Never mow while people (especially children) or pets are
nearby.
41
Enabling child protection
Child protection prevents accidental use of Robomow by little children.
When child protection is enabled, Robomow will require a special
combination to start a mowing operation or to go back to its base.
To enable child protection, press and hold the GO + STOP buttons
together for 6 seconds.
If you wish to disable child protection, press
and hold the GO + STOP buttons together for 6
seconds again.
Alternatively, child protection can be enabled or
disabled conveniently via the mobile app (RX20
Pro and RX20u models only).
Powering up Robomow
To power up Robomow, press and hold the GO button for 2 seconds until
the ON/OFF indication is lit.
When you need to switch Robomow off, simply press and hold GO button
for 2 seconds, until the ON/OFF indication goes off.
Note: If the theft protection is
enabled (RX20 Pro/RX20u models),
you will need to unlock your
Robomow via the mobile app
before you can switch it off.
2 seconds
6 seconds
42
Starting a mowing operation
Starting a mowing operation is super easy!
If you wish to start a regular
mowing operation (up to 2 hours
of continuous mowing), all you need
to do is to press the GO button once.
If the regular mowing duration
is too long for your lawn, you can
initiate a short mowing operation
(of up to 60 minutes) by pressing
the GO button twice.
When child protection is enabled,
a special combination of keys
is required to start a mowing
operation. Hold down the STOP
button and press the GO button
once to unlock the child protection
for 30 seconds. The Lock indication
will be temporarily switched off.
Now you can start a mowing
operation as described above. As
soon as the mowing operation is
started, the child protection will
automatically relock itself.
X 1
X 2
X 1
43
Stopping an operation
To stop any current operation, press the STOP / button.
Sending Robomow to its base
To send Robomow to its base, simply press the STOP /
button when Robomow is inside the lawn.
If child protection is enabled, see the “Starting mowing
operation” section above to temporarily unlock it. Then press
STOP / button to send Robomow to its base. The child
protection will relock automatically.
Automatic charging
Once a mowing operation is finished, Robomow automatically
returns to its base station for charging to be ready for the next
operation.
How much mowing does your lawn need?
The amount of mowing depends on a season and on the size
of your lawn. We recommend the following amounts of weekly
mowing times per lawn size in peak season.
Lawn size Recommended weekly mowing times
Up to 50 m
2
2 hours
50 -100 m
2
4 hours
100 -150 m
2
6 hours
150 - 200 m
2
(RX20u / RX20 Pro only)
9 hours
44
Along with a totally exciting experience, it brings additional options and
capabilities to your small and clever mower:
Setting automatic mowing schedule
Activating theft protection
Defining additional starting points
Remote controlling with manual mowing
Remote diagnostics by a service station
Additional options
with the mobile app
(RX20 Pro/ RX20u models only)
Robomow RX is a smart connected product. It comes with a built-in
Bluetooth LE (Low Energy) device that enables you to control your mower
from your smartphone.
A free complementary mobile app will allow you to experience your
Robomow RX20u or RX20 Pro in a whole different way!
You can download the app (Android version only) by
scanning this QR code.
45
Taking care of your
Robomow
Once a month:
Inspect the underside of the mower. Clean if necessary. Carefully
scrape the collected grass debris from under the mowing deck.
Most grass accumulation can be removed using a small stick or
similar object.
Periodically inspect the Base Station, clean it from mud and debris to
allow proper docking.
Periodic maintenance
To allow better maintenance and to keep Robomow in good condition, it is
recommended to take your Robomow to a certified Robomow dealer for
service prior to winter storage.
WARNING
Severe injury hazard!
Always turn the Safety Switch off before lifting the mower. The
blade is very sharp. It can cause severe cuts or lacerations. Always
wear heavy work gloves when working with or around the blade.
NEVER use a damaged or broken blade. Use only sharp blade.
IMPORTANT!
NEVER use high pressure water to clean the mower.
Liquids can damage components. Use only a damp or
wet cloth to wipe the surface clean after scraping.
46
Operating the Disabling Device
The Disabling Device prevents the operation of Robomow when it is
removed.
If the Disabling Device is pulled out, the current operation will be
immediately halted, the Lock indication will blink three times and the
ON/OFF LED will switch off.
If any button on Robomow’s operating panel is pressed, the Lock
indication will blink three times to indicate that the Disabling Device is
missing.
If theft protection is enabled, it will remain active even though the
Disabling Device is removed.
Replacing the blade
1. Power Robomow off by pressing GO button for 2 seconds.
47
2. Remove the Disabling Device.
3. Put on heavy-duty gloves, and place RoboTool over
the blade so that it covers the whole blade.
4.Use the provided Allen tool (comes with a replacing blade) to unscrew
the screws while holding the blade with the RoboTool.
5. Replace the blade with a new one (Part No. MRK9100A).
6. Make sure to close both screws tightly.
Lift
Pull
48
Winter storage
Robomow
Charge Robomow fully in its base
Switch it off by pressing the GO button for 2 seconds
Store in dry indoor conditions at ambient temperatures above 0˚C.
Base Station
No winter storage is required for a Base Station. It can be left on the
lawn during the winter period.
It is recommended to disconnect the Power Supply from the mains
during the winter storage period.
Winter service
To allow better maintenance and to keep Robomow in good condition, it
is recommended to bring your Robomow to a certified Robomow dealer
for service prior to winter storage.
Winter service includes operations like cleaning the mower’s parts and
mowing deck, checking for worn parts (such as blade, drive wheels and
other moving parts) and replacing them if required, testing the mower’s
functions and safety components, checking the battery, and uploading
a latest software version, possibly including newly added features.
No. of
beeps
ON-OFF
indication
Meaning Corrective action
Blinking red Mower crossed
outside / mower
is stuck in place /
lift event detected/
wrong wire connection
Check that the Perimeter Wire is
not too close to the edge or not on
a sloped area.
Move the mower inside the lawn or
away from this particular location
and renew the operation.
Check the ground ditches. Fill with
dirt and level off.
Swap wire connections at the base
station head
• • Blinking red Check the blade /
mow motor overheat
Remove the Disabling Device and
inspect the blade for foreign mate-
rial or debris preventing rotation.
Increase cutting height.
• • • Blinking red No wire signal /
waiting for signal /
wire is cut
Confirm power supply is plugged
into the power outlet.
Check power supply and perim-
ter wire connection to the Base
Station.
Check the indication on the Base
Station. If the wire is cut, repair is
with the provided wire conenctors.
• • • • Blinking red Check drive wheels /
drive motor overheat
Check the drive wheels and
remove grass or other objects.
49
Troubleshooting
Simple troubleshooting steps
In case of a fault, the Robomow On/Off indication will light up in red. Press any
button to check for an optional sound indication for the fault. The table below will
guide you to the corresponding action to take.
No. of
beeps
ON-OFF
indication
Meaning Corrective action
None Blinking red
(two LEDs)
No power supply /
charging problem
Confirm power supply is plugged
into the power outlet.
Confirm a good connection of the
power supply to the Base Station.
Clean the charging pins.
None Steady red Other faults Check in the mobile app* or call
Robomow service.
50
* Confirm a good connection between the power supply and the Base Station
(*) All faults and corresponding corrective actions are communicated and described
in the app as well. This feature is available for all RX models with production year
2017 (including RX12u).
52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

robomow-rx20u
  • Mein Robomow beendet nach 30 Minuten das Mähen, trotz vollständiger Aufladung,Was kann die Ursache sein, außer dem Akku? Ist 2 1/2 Jahre alt u. wurde wenig benutzt. Eingereicht am 15-4-2021 19:22

    Antworten Frage melden
  • Unser rx20u möchte nach dem Winterschlaf nicht mähen... Eingereicht am 31-3-2021 13:28

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Robomow RX20u wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Robomow RX20u

Robomow RX20u Bedienungsanleitung - Deutsch - 60 seiten

Robomow RX20u Bedienungsanleitung - Holländisch - 60 seiten

Robomow RX20u Bedienungsanleitung - Französisch - 60 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info