Bedienungsanleitung Robomow TC1000 (Seite 40 von 52) (Englisch)

644648

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Display Message Probable Cause/Event Correcve Acons

E 6

Check Drive

- Grass or other object has wrapped

around the drive wheel.

- The drive motors have been

working under severe load for too

long.

- Check the drive wheels and remove the

grass or other objects.

E 7

Front Wheel

Problem

- The Front Wheel has left the

ground for too long during

operation.

- If Robomow has driven onto an obstacle,

Switch off the Safety Switch, raising the front

end: Remove or exclude the object from the

mowing area.

- If Robomow is being used on a slope too

steep for safe mowing, exclude this from the

mowing area.

- If high grass is preventing the front wheel

from fully turning on the ground, raise the

cutting height.

- If the ground contains large holes or

indentations where the front wheel can drop

into when passing across, ll these areas

with dirt and level off.

E 8

Decrease

Inactive Time

- Too many Inactive Days and/or

Hours have been set for your lawn

area. Current settings will not be

changed.

- Mowing Frequency is too high for

current settings of Inactive Time.

The Inactive Time settings will be

set to defaults.

- Area setting is too high for current

settings of Inactive Time. The

Inactive Time settings will be set to

defaults.

- Decrease the number of Inactive Days and/

or the number of Inactive Hours to allow

Robomow to complete mowing your lawn.

- Decrease Mowing Frequency (see p001 in

the table in Section 6.4.2)

- Decrease Area setting

E 9

See

Troubleshooting

in Manual

- E 9 is displayed for all other

messages that are not listed in the

above table.

- Press the ‘Right arrow’ button to receive the

stop reason number and refer to the next

table for more details about the stop reason,

causes, and actions.

9.2 Detailed Error Codes

If the above table (Section 9.1) does not give enough information to help solve the problem, then press the LEFT

arrow while the error code is displayed in order to receive a number that gives more details about the problem

and refer to the table below:

Display Message Probable Cause/Event Correcve Acons

0010

Mow Overheat

- The mowing motor has been

working under a severe load for too

long.

- No need for action – Robomow will renew

automatically the operation after the mowing

motor will cool down.

0011

Drive Overheat

- The drive motors have been working

under a severe load for too long.

- No need to do anything.

- Robomow will renew the operation

automatically as soon as the drive motor will

cool down.

0012

No wire signal - See E3 in the above table

0014

Front wheel

problem

- See E7 in the above table

0015

Button pressed

- One of the operating panel buttons

is constantly pressed.

- Press ‘OK’ to conrm the message and

continue operation. This message is displayed

to inform only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow TC1000 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow TC1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info