Bedienungsanleitung Robomow Tuscania 500 (Seite 72 von 268) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

512484

Zoom out

Zoom in

Vorherige Seite

1/268

Nächste Seite

Add pegs in to pull

the perimeter wire down

to the ground surface,

below the grass tips.

Add pegs in to pull

the perimeter wire down

to the ground surface,

below the grass tips.

Important

If the lawn's edge borders with a pond, swimming pool or watercourse or where the grass level is

higher than 70cm (2ft) from the edge around it, then it is required to keep a distance of at least 1.2m

(4ft) between the wire and the water (or chasm) otherwise supplement a fence or the same along the

lawn's edge, so Robomow can detect it. The height must then be at least 15cm (6 inch). This will

prevent Robomow, under any circumstances, from crossing the wire outside the working area

1.4.3 Fastening the Wire to the Ground

 It is not necessary to bury the perimeter wire, though you may do so if you wish, up to 10 cm

(4 inches) deep.

 Small pegs or stakes are supplied with the Robomow and they are used to fasten and hold the

perimeter wire to the ground, below grass level.

 Initially place a minimum number of pegs to fasten the wire down. Remember that you will want to

test the wire set up before you fill in additional pegs and you may find some areas where you will

need to move the wire position slightly.

 Upon hammering the peg to its final depth in the ground, pull the wire tight. It is a lot easier to insert

pegs into wet soil. If the soil is dry, water the yard before perimeter wire set up.

 Pegs should be driven at distances between one

another that will keep the wire down below the

grass level and prevent it from becoming a tripping

hazard (Figure 1.14).

 When properly fastened to the ground, the wire and

pegs will soon disappear under the growth of new

grass and will not be visible.

 If additional wire is required in order to complete

the set-up, use the wire connectors provided, which

are water-proof, to connect between the two wire

ends, as explained in chapter 5.6.

WARNING!

Damage to the eye is possible. Use proper eye protection and wear

appropriate work gloves when hammering the pegs. Hard or dry ground

may cause pegs to break when driving them in. In extreme cases,

watering the lawn where the pegs will be driven can be beneficial.

IMPORTANT INFORMATION!

Screw terminals or twisted cables, insulated with insulation tape is not a satisfactory splice. Soil

moisture will cause the stripped wire ends to oxidize and after a while result in broken circuit.

Figure 1.14 -

Pegging the Perimeter Wire

Short distance of

RoboRuler - where the

area outside the

immediate perimeter is

free of obstacles and is the

same relative height as the

perimeter edge or lower

Long distance of

RoboRuler – where the

area outside the

immediate perimeter has

obstacles or differences in

the height along the

perimeter edge

Figure 1.13 –

Using the RoboRuler

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow Tuscania 500 Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info