Bedienungsanleitung Rockford Fosgate 3 SIXTY.3 (Seite 1 von 28) (Englisch)

602239

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Serial Number:

Date of Purchase:

Installation & Operation

INTERACTIVE

SIGNAL PROCESSOR

3SIXTY.3

Quick Setup Guide

1. Install 3Sixty.3 software

2. Open 3Sixty.3 Software (See pg 9)

3. Connect 3Sixty.3 USB cable to 3Sixty.3 and then to the PC. (See pg 9)

4. Open the 3Sixty.3 user interface (UI). A pop up window will appear telling you the unit is not conﬁgured.

Click “OK” (See pg 10)

5. If the conﬁguration pop up window above does not appear telling you that the unit is not conﬁgured,

open the “Device” tab and select “Conﬁguration” in the top left corner. (See pg 9)

6. When the input conﬁguration page appears, select your source interface type and label your input

channels. Click “Next” (See pg 15)

7. When the output conﬁguration page appears, label your output channels if one or more channels is not

being used select “Not Connected”. Click “Next” (See pg 15)

8. When the input channel summing page appears, select the output channel from the vehicle illustration,

then select the input(s) you would like to use/sum to create that output channel. After assigning ALL

output channels there inputs, Click “Next” (See pg 15)

9. When the assign source presets page appears, select the preset(s) you would like to assign to each

source. Click “Next” (See pg 16)

10. When the input level setup prompt appears, insert the 3Sixty.3 setup disk and play track #1 at max

volume and follow the on screen directions. Click “Next”(Outputs will be muted) (See pg 16)

11. When the adjust source level appears, reduce the volume of the source until all the level meters are

green. Click “Next” (The 3Sixty.3 is not looking for a hard clipped signal you would typically see when

level setting an ampliﬁer) (Make a note of the MAXIMUM volume level on the source unit achieved

keeping the level meters green for future steps) (See pg16)

12. When the input attenuator controls appears, select “Auto Range” to automatically match the input

voltage, to the input voltage range of the DSP. (See pg 16)

13. a) If using a low level input, the mute warning page will appear prompting you to reduce your

volume. Click “Finish” and go to Step #15 (See pg 17)

b) If using a high level input, the input denormalization setup prompt appears, use the 3Sixty.3 setup

disk and play track #2 at half of the noted source volume in step #11. Click “Next” (See pg 17)

14. During the input normalization page, select “Auto Normalize”. This may take up to 5 min. Once

completed, Click “Next” (See pg 17)

15. The mute warning page will appear prompting you to reduce your volume, and Click “Finish”. Device

setup is now complete. Please proceed with system tuning.

16. Select the crossover type, class, slope, and frequencies for each channel. (See pg 13 & 21)

17. Level set the ampliﬁers to the main source unit, then adjust each additional source level. (See pg 14

& 22)

18. Select the time delay for each channel. (See pg 14 & 28)

19. Adjust the EQ for each channel, for each source or preset. (See pg 14 & 28)

20. After adjusting the EQ, level set the ampliﬁers to the main source unit, then adjust each additional

source level. (See pg 22)

21. Under the ”File” tab select “Save File”. (See pg 10)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rockford Fosgate 3 SIXTY.3 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Rockford Fosgate 3 SIXTY.3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info