1. In the “Devices” tab select “Preferences” then “General” then “EQ Delay Units”. This will let you select the unit of measure you would like to enter the
delay in.
2. The simplest way to measure delay is with a tape measure. With the driver sitting in the drivers seat, and the seat adjusted to their driving position,
measure the distance of each speakers on the right from there mounted location to the drivers right ear. Repeat for the left side of the vehicles only this time
measure the distance of each speakers on the left from there mounted location to the drivers left ear.
3. Looking at all the distance measurements for each speaker find the distance that is the longest of all the speakers (usually the subwoofers). Select the
speaker with the furthest distance from the speaker illustration on the main page and enter 0 into its “Delay” text box. For each of the remaining speakers
take the longest distance measurement value and subtract that speakers specific distance from it. The resulting value for each speaker is the delay distance
that needs to be entered into its “Delay” text box for that speaker.
31 Band EQ
Adjusting the Main Source
1. Before adjusting the EQ you will need to setup a real time analyzer (RTA) to continuously measure the cars frequency response. Place the micro phone(s)
as close to the location of the drivers head as possible. Insert the 3Sixty.3 setup disk into your source unit and select the “Pink Noise” track. Adjust the
volume on the source unit to half its maximum volume found earlier in the “Configuring the input section” of the manual.
2. To adjust a band of the EQ, select it by either clicking on it with the mouse or entering its band number in the “EQ band” text box you can adjust the
bands, frequency, level, and Q. The default band frequencies are in 1/3 octave increments however to change a specific center frequency, level, or Q of a
band, select the band you would like to adjust and then entering the new value in its frequency text box or move the slide to the new value.
3. Once the EQ adjustment has been completed, in the “Devices Tab” select “Store Preset”. You can now select which of the four preset positions you would
like to save the EQ settings to. However since the “Main” source input was used to tune the system, this preset should be saved under the preset number(s)
you assigned to the main input in the “Assign Source Presets” section of the “Configuration”. That way it will/can be recalled when the “Main” source is
selected as the input on the wired remote control.
Adjusting the BT Source
Open the “Wired Remote Control (WRC) simulator at the top of the page. Select BT for the source from the “Source” drop down menu and close the
simulator page. Follow the same steps as above for “Adjusting the Main Source” only using the BT device as the source for the “Pink Noise” track. Be sure
to select a different preset when saving the EQ settings. Remember since the “BT” source input was used to tune the system, this preset should be saved
under the preset number(s) you assigned to the BT input in the “Assign Source Presets” section of the “Configuration”. That way it will/can be recalled
when the BT source is selected as the input on the wired remote control.
Adjusting the AUX Source
Open the “Wired Remote Control (WRC) simulator at the top of the page. Select AUX for the source from the “Source” drop down menu and close the
simulator page. Follow the same steps as above for “Adjusting the Main Source” only using the AUX device as the source for the “Pink Noise” track. Be
sure to select a different preset when saving the EQ settings. Remember since the “AUX” source input was used to tune the system, this preset should be
saved under the preset number(s) you assigned to the AUX input in the “Assign Source Presets” section of the “Configuration”. That way it will/can be
recalled when the AUX source is selected as the input on the wired remote control.
Adjusting the Optical Source
Open the “Wired Remote Control (WRC) simulator at the top of the page. Select Optical for the source from the “Source” drop down menu and close the
simulator page. Follow the same steps as above for “Adjusting the Main Source” only using the Optical device as the source for the “Pink Noise” track. Be
sure to select a different preset when saving the EQ settings. Remember since the “Optical” source input was used to tune the system, this preset should be
saved under the preset number(s) you assigned to the Optical input in the “Assign Source Presets” section of the “Configuration”. That way it will/can be
recalled when the Optical source is selected as the input on the wired remote control.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Rockford Fosgate 3 SIXTY.3 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
