Bedienungsanleitung Rockford Fosgate PMX-2 (Seite 6 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

662891

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Installation / Mounting

Contents

Installation Considerations

The following is a basic list of tools needed for installation:

This section focuses on some of the vehicle considerations for installing

your new source unit. Pre-planning your system layout and best wiring

routes will save installation time. When deciding on the layout of your

new system, be sure that each component will be easily accessible for

making adjustments.

If you feel unsure about installing this system yourself, have it installed

by a qualiﬁed Rockford Audio technician.

Before installation, disconnect the battery negative (-) terminal to prevent

damage to the unit, ﬁre and/or possible injury.

Before beginning any installation, follow these simple rules:

1. Be sure to carefully read and understand the instructions before

attempting to install the unit.

2. For safety, disconnect the negative lead from the battery prior to

beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting

your unit in place.

4. Route all of the RCA cables close together and away from any high

current wires.

5. Use high quality connectors for a reliable installation and to minimize

signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel

lines, brake or hydraulic lines, vacuum lines or electrical wiring when

working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the

vehicle provides the best protection.

8. Avoid running wires over or through sharp edges. Use rubber

or plastic grommets to protect any wires routed through metal,

especially the ﬁrewall.

9. ALWAYS protect the battery and electrical system from damage with

proper fusing. Install the appropriate fuse holder and fuse on the

+12V power wire within 18” (45.7 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from

the metal to ensure a good, clean ground connection. Grounding

connections should be as short as possible and always be connected

to metal that is welded to the main body, or chassis, of the vehicle.

Seatbelt bolts should never be used for connecting to ground.

• Volt/Ohm meter

• Wire strippers

• Wire crimpers

• Wire cutters

• #2 Phillips screwdriver

• Battery post wrench

• Hand held drill w/ assorted

bits

• Heat shrink tubing

• Soldering iron

• Solder

• Heat gun

• 7mm wrench

• Source Unit

• Trim Bezel

• Mounting Plate

• U Bracket

• Screws

• Power / Speaker Harness

• Installation & Operation

Manual

Mounting (Using Mounting Plate)

To mount the unit, you will need to ﬁnd a ﬂat surface with adequate

clearance behind it that provides enough clearance for the unit and all it’s

necessary wiring.

1. Once you have determined a mounting location, you will need to cut

a circular hole 3” (77mm) in diameter.

2. After the hole is cut slide the unit and wiring through the hole.

3. Slide the mounting plate over the backside of the unit and secure with

the supplied screws.

4. Press on the trim bezel to the front side of the unit.

5. Plug in all wiring harnesses and cables. Refer to the wiring diagram

for wire harness connection types.

Mounting (Using U Bracket)

To mount the unit, you will need to ﬁnd a ﬂat surface with adequate

clearance behind it that provides enough clearance for the unit and all it’s

necessary wiring.

1. Once you have determined a mounting location, you will need to cut

a circular hole 3” (77mm) in diameter.

2. After the hole is cut slide the unit and wiring through the hole.

3. Take the U bracket and slide over the two studs on the back of the

unit. Tighten down with supplied nuts.

4. Press on the trim bezel to the front side of the unit.

5. Plug in all wiring harnesses and cables. Refer to the wiring diagram

for wire harness connection types.

Trim Bezel

Panel

Bracket

Mounting Screws

Mounting Plate

Source Unit

Nuts

Panel

Trim Bezel

Panel

Bracket

Mounting Screws

Mounting Plate

Source Unit

Nuts

Panel

Trim Bezel

Fig. 4

Fig. 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rockford Fosgate PMX-2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info