Bedienungsanleitung Rockford Fosgate R250-1D (Seite 6 von 20) (Englisch)

602251

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Contents

•R250-1D, R500-1D or R500-1 - Prime Mono Channel Ampliﬁer

•Mounting Hardware

•Installation & Operation Manual

Installation Considerations

The following is a list of tools needed for installation:

This section focuses on some of the vehicle considerations for install-

ing your new ampliﬁer. Pre-planning your system layout and best wiring

routes will save installation time. When deciding on the layout of your new

system, be sure that each component will be easily accessible for making

adjustments.

If you feel unsure about installing this sys-

tem yourself, have it installed by a qualiﬁed

technician.

Before installation, disconnect the battery neg-

ative (-) terminal to prevent damage to the unit,

ﬁre and/or possible injury.

Before beginning any installation, follow these simple rules:

1. Be sure to carefully read and understand the instructions before

attempting to install the unit.

2. For safety, disconnect the negative lead from the battery prior to

beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting

your unit in place.

4. Route all of the RCA cables close together and away from any high

current wires.

5. Use high quality connectors for a reliable installation and to minimize

signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel

lines, brake or hydraulic lines, vacuum lines or electrical wiring when

•Fuse-holder and fuse. (See

speciﬁcations for fuse rating)

•Volt/Ohm Meter

•Wire strippers

•Wire crimpers

•Wire cutters

•#2 Phillips screwdriver

•Battery post wrench

•Hand held drill w/assorted bits

•Assorted connectors

•Adequate Length—Red

PowerWire

•Adequate Length—Remote

Turn-onWire

•Adequate Length—Black

GroundingWire

working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the

vehicle provides the best protection.

8. Avoid running wires over or through sharp edges. Use rubber or

plastic grommets to protect any wires routed through metal, especially

the ﬁrewall.

9. ALWAYS protect the battery and electrical system from damage with

proper fusing. Install the appropriate fuse holder and fuse on the +12V

power wire within 18” (45.7 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from

the metal to ensure a good, clean ground connection. Grounding

connections should be as short as possible and always be connected

to metal that is welded to the main body, or chassis, of the vehicle.

Seatbelt bolts should never be used for connecting to ground.

Mounting Locations

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the

engine compartment will void your warranty.

Trunk Mounting

Mounting the ampliﬁer vertically or inverted will provide adequate cool-

ing of the ampliﬁer. Mounting the ampliﬁer on the ﬂoor of the trunk will

provide the best cooling of the ampliﬁer.

Passenger Compartment Mounting

Mounting the ampliﬁer in the passenger compartment will work as long as

you provide a sufﬁcient amount of air for the ampliﬁer to cool itself. If you

are going to mount the ampliﬁer under the seat of the vehicle, you must

have at least 1” (2.54cm) of air gap around the ampliﬁer’s heatsink.

Mounting the ampliﬁer with less than 1” (2.54cm) of air gap around the

ampliﬁer’s heatsink in the passenger compartment will not provide proper

cooling and will severely affect the performance of the ampliﬁer and is

strongly not recommended.

Battery and Charging

Ampliﬁers will put an increased load on the vehicle’s battery and charging

system. We recommend checking your alternator and battery condition

to ensure that the electrical system has enough capacity to handle the

increased load of your stereo system. Stock electrical systems which are

in good condition should be able to handle the extra load of any Prime

Series ampliﬁer without problems, although battery and alternator life can

be reduced slightly. To maximize the performance of your ampliﬁer, we

suggest the use of a heavy duty battery and an energy storage capacitor.

Wiring the System

If you do not feel comfortable with wiring your

new unit, please see your local Authorized

Rockford Fosgate Dealer for installation.

Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rockford Fosgate R250-1D Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info