Bedienungsanleitung Rockford Fosgate t1000 4 (Seite 7 von 64) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

168821

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

INSTALLATION

3. Trim the RED wire (power cable) within 18" of the battery and splice in a inline fuse holder (not

supplied). See Specifications for the rating of the fuse to be used. DO NOT install the fuse at

this time.

4. Strip 1/2" from the battery end of the power cable and crimp a large ring terminal to the cable. Use

the ring terminal to connect to the battery positive terminal.

5. Prepare the BLACK wire (Ground cable) for attachment to the amplifier by stripping 7/8" of

insulation from the end of the wire. Insert the bare wire into the GROUND terminal and tighten the

set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the

metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and

attach a ring connector.Fasten the cable to the chassis using a non-anodized screw and a star washer.

NOTE:Keep the length of the BLACK wire (Ground) as short as possible.Always less than 30"(76.2cm).

6. Prepare the Remote turn-on wire for attachment to the amplifier by stripping 7/8" of insulation from

the end of the wire. Insert the bared wire into the REMOTE terminal and tighten the set screw to

secure the wire in place. Connect the other end of the Remote wire to a switched 12 volt positive

source.The switched voltage is usually taken from the source unit's remote amp on lead. If the source

unit does not have this output available, the recommended solution is to wire a mechanical switch in

line with a 12 volt source to activate the amplifier.

7. Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on

cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road

vibration or sudden vehicle stops.

8. Connect from source signal by plugging the RCA cables into the input jacks at the amplifier.

NOTE:All “ACTIVE” inputs must have RCA jacks connected. Switch in 2CH. position,“ACTIVE” - Front

channel inputs only.Switch in 4CH.position,“ACTIVE” - All Front and Rear channel inputs.When

connecting to the 4-Channel inputs, be sure to route both front and rear RCA cables tightly

together.

CAUTION:Always ensure power is off or disconnected at the amplifier before

connecting RCA cables. Failure to do so may cause injury,damage to the

amplifier and/or connected components.

9. Connect the speakers. Strip the speaker wires 1/2" and insert into the speaker terminal and tighten

the set screw to secure into place. Be sure to maintain proper speaker polarity.DO NOT chassis

ground any of the speaker leads as unstable operation may result.

10. Perform a final check of the completed system wiring to ensure that all connections are accurate.

Check all power and ground connections for frayed wires and loose connections which could cause

problems. Install inline fuse near battery connection.

NOTE:Follow the diagrams for proper signal polarity.

Power

Connection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rockford Fosgate t1000 4 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info