Bedienungsanleitung Rocktrail HG11019 - IAN 445239 (Seite 18 von 75) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

819483

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

14 GB/IE

Assembly

The product should be assembled by two people.

Carry out a test setup before your trip. Make sure

the product and all components are complete and

undamaged.

Erecting the tent

1. Open the carry bag [4] and take out the

contents.

2. Remove all components and spread the tent

[1] ﬂat on the ground with the tunnel guides

facing upwards (Fig. A).

3. Assemble the ﬁbreglass poles [2] and guide

them through the tunnel guides of the tent [1]

(Fig. A).

4. Bend the ﬁbreglass poles [2] and put their

ends over the pins of the metal rings at each

corner of the tent [1] (Fig. B).

5. Stand the tent upright [1] (Fig. B).

6. Secure the tent [1] to the ﬁbreglass poles [2]

with the plastic hooks (Fig. B).

7. Stretch the tent ﬂoor so that there are no

creases in it and secure each corner with a

ground peg [3] (Fig. C).

8. Stake out the guy lines at each corner of

the tent [1] and secure each guy line with a

ground peg [3] (Fig. D).

Note: make sure the product is not under too

much tension.

Note: check the tensioning of the tent depending

on the weather.

Use

There is a hook inside the product where you

can hang a camping light, for example (not

included in the package contents).

The tent’s inner pockets can be used for daily

items or clothing.

Note: water condensation generally occurs in

all tents, but especially when there are strong

temperature ﬂuctuations.

After a night in the tent, there will be water

condensation drops on the inside surface.

Condensation is not a sign of leaks. Good

ventilation reduces condensation inside the tent.

Open the tent entrances and windows regularly to

reduce condensation inside the tent.

Opening doors and windows

1. Open the zips of the outer fabric.

2. Roll up the outer fabric.

3. Fasten the toggles to prevent them from

unrolling.

4. If necessary, open the zips of the inner fabric.

5. Roll up the inner fabric.

6. Fasten the toggles to prevent them from

unrolling.

Closing doors and windows

1. Release the toggles.

2. Roll down the fabric.

3. Close the zip.

Dismantling the tent

Note: dismantle the product in as clean and dry a

condition as possible, so as to avoid the formation

of mould or stains. After dismantling in the rain,

let the product dry out completely before packing

it away. Clean all components thoroughly before

packing them away.

1. Remove all ground pegs [3] (Fig. C & D).

2. Roll up the guy lines.

3. Release the plastic hooks from the ﬁbreglass

poles [2] (Fig. B).

4. Remove the ﬁbreglass poles [2] from the pins

of the metal rings (Fig. B).

5. Pull the ﬁbreglass poles [2] out of the tunnel

guides of the product (Fig. A).

6. Pull the ﬁbreglass poles [2] apart and fold

them up.

7. Spread the tent [1] out ﬂat.

8. Fold the tent [1] lengthways to about one ﬁfth

of its width, then crosswise twice.

9. Put the tent [1], ﬁbreglass poles [2] and the

ground pegs [3] in the carry bag [4] and

close.

Repairs

Small tears or holes in the fabric can be

repaired with standard repair patches.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rocktrail HG11019 - IAN 445239 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info