Bedienungsanleitung Rodek r 1500 a 2 (Seite 26 von 32) (Deutsch, Englisch)

167804

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

3. ELECTRICAL WIRING

3.3 CONNECTION OF POWER CABLES

Run the positive power cable ("+12 V") directly from

the positive terminal of the car battery to the amplifier.

Make sure the power cable makes good contact to the

battery; i.e. use an appropriate battery clamp that ac-

cepts big gauge power cables! For protection of your car

audio system and your entire car against electrical fire

hazards from a short-circuit of the main power cable

with chassis ground, you must insert a main fuse (holder)

within the first 30cm of the battery. The fuse type/value

should be matching the limitations of your main power

cable and the requirements of your car audio system.

Preferably a minimum of 80 Amperes with this amplifier

and an appropriate power cable cross-section.

Now you route the ground cable to the amplifier. It is best

to keep the ground cable ("-12V") as short as possible,

i.e. to find a chassis contact very close to the amplifier.

The ground power cable must have the same cross-sec-

tion as the positive power cable. It is recommended to

use a corrosion-resistant gold-plated power ring or a

massive ground clamp between the ground cable and

the chassis ground point. Keep in mind that audible

interferences and problems originating in the power

supply of the amplifier, are mostly based on a bad ground

contact. So a good (and clean) grounding to the vehicle

chassis is absolutely crucial, to obtain best performance

of your amplifier.

Especially the music signal cables (RCA interconnects)

should be kept far away from any potential sources of

electrical interference i.e. electronic vehicle manage-

ment systems (engine computers, relays etc.) fuel

pumps, wiring harnesses etc.!

3.1 RCA INTERCONNECTS / REMOTE

LEAD

Carefully run the RCA audio signal interconnect(s) and

the remote switching cable from the head-unit to the

amplifier. The audio signal cables should be routed com-

pletely separate from the power cables. Use only double

or triple shielded quality cables!

Connect the remote wire lead to the remote output of the

head-unit and to the remote input terminal of the ampli-

fier. Finally connect the RCA interconnect cable(s) to the

respective outputs on the head-unit and the RCA inputs

of the amplifier.

3.2 LOUDSPEAKER CABLES

Connect the loudspeaker wires to the speaker terminals

of the amplifier. Use good quality wires of 2.5mm² cross-

section. You will need a set of Allen wrenches for the con-

nection of the wires!

When baring wires, remove approximately 6-8mm of

the insulation and after axially twisting the wires; insert

the bare ends into the corresponding speaker terminal

output on the amplifier. Be sure to follow correct polarity

("+" to "+"; "-" to "-"). Tighten the terminal screws on

the amplifier.

R1500-4100A2 Manual.indd 26R1500-4100A2 Manual.indd 26 07.07.2004 10:59:11 Uhr07.07.2004 10:59:11 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rodek r 1500 a 2 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info