622363

Roland A-01 Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/1
Nächste Seite
7
Top panel
1
Ribbon controllers (C1, C2)
These are touch-type controllers.
* From the left, they are numbered C1 and C2.
2
Operation buttons
Use these to make settings for the A-01.
3
Rotary encoders (R1–R4)
Use these to control external devices.
(Subsequently, we’ll call these “encoders.”)
* From the left, they are numbered R1, R2, R3,
and R4.
4
Bluetooth LED
This LED is lit blue when a Bluetooth connection
is enabled.
7
Rear panel
5
[POWER] switch
Turns the power on/o.
* Before turning the unit on/o, always be
sure to turn the volume down. Even with
the volume turned down, you might hear
some sound when switching the unit on/o.
However, this is normal and does not indicate
a malfunction.
6
Micro USB port
Connect this to your computer so that MIDI data
can be transferred.
7
[VOLUME] knob
Adjusts the output of the built-in speakers,
PHONES jack.
8
PHONES jack
Connect your headphones here.
9
CV OUT jack, GATE OUT jack
MIDI messages from the A-01 or from an external
device are converted to single-note CV/GATE
signals and output from these jacks.
10
MIDI IN connector, MIDI OUT connector
Connect these to your MIDI equipment to receive
or send MIDI messages.
Connecting Your Equipment
Connecting a computer
1.
Using a commercially available USB cable (A-micro B-type), connect the A-01 to your computer
and turn on the power of the A-01.
2.
Start the DAW or sequencer software that you’re using, and specify the A-01 as the MIDI device.
Connecting a tablet
You’ll use the Bluetooth function to connect the A-01 to your tablet.
1.
Power-on the A-01, and place your tablet nearby.
2.
Enable the Bluetooth function of your tablet, and in the list of detected devices, choose “Roland
A-01.”
When the connection is established, the A-01’s Bluetooth LED is lit.
3.
Start the app that you’re using, and specify the A-01 as the Bluetooth MIDI device.
2 3
4
1
5 6 7 8 9 10
CAUTION
Take care not to connect these jacks to your
headphones or earphones. Doing so will cause
malfunctions.
By using the A-01 in conjunction with
the separately sold K-25m keyboard
unit, you can use it as a synthesizer
equipped with a keyboard.
Panel Descriptions
SEQ mode contains settings for the entire pattern (16 steps) and settings for each individual step.
Playing/stopping the pattern
To play the pattern, press the [
s
] button. To stop the pattern, press the [
s
] button once again.
Settings for the entire pattern
1.
As shown in the table below, make settings for the entire pattern.
Parameter Explanation Controller
Step Species the number of steps (1–16). Encoder (R1)
Shue Adjusts the rhythmic swing of the notes. Encoder (R2)
Step Order
Species the playback order of the steps.
Normal Normal (default)
EvenOdd
Invert even/ odd-
numbered
Odd Odd-numbered only
Even Even-numbered only
O
0
E
Odd-numbered only
0
Even-numbered only
E
0
O
Even-numbered only
0
Odd-numbered only
Random Random
Encoder (R3)
Tempo
Species the tempo (40–240 bpm) of the pattern.
* The [MENU] button blinks at the specied tempo.
Encoder (R4)
Gate Time
Species the same note duration for all steps.
* It is not possible to enter a tie in the overall settings. To enter a tie,
make settings for each individual step.
Ribbon
controller (C2)
Scale
Select one of the
following four as the
note length value of
each step.
[INC], [DEC]
button
O Step
Inputs the “Rest“ or “Skip“ to all blank steps.
Rest: Hold down a [1]–[4] button and press [
C
] button.
Skip: Hold down a [1]–[4] button and press [
A
] button.
—
Creating a pattern: Inputting and editing steps
1.
Use the [C][A] buttons to select the block that you want to input.
2.
Use the [1]–[4] buttons to enter (turn on/o) each step.
* Enter a tie: Hold down a [1]–[4] button and press [INC] button.
Enter a tie O: Hold down a [1]–[4] button and press [DEC] button.
3.
As shown in the table below, specify how each step will sound.
Parameter Explanation Editing procedure
Key Species the pitch of the step.
Hold down a [1]–[4] button and
turn the encoder (R1).
Gate Time
Species the duration of the note.
To enter a tie, set this value to 101%.
Hold down a [1]–[4] button and
turn the encoder (R2).
Cuto Species the cuto frequency of the low pass lter.
Hold down a [1]–[4] button and
turn the encoder (R3).
Resonance
Emphasizes the overtone components in the region of
the low pass lter’s cuto frequency.
Hold down a [1]–[4] button and
turn the encoder (R4).
Velocity Species the strength (velocity) of the note.
While holding down one of the
[1]–[4] buttons, press the [
I
]
button and turn encoder (R1).
4.
Repeat steps 1–3 to create your pattern.
Recalling or saving a pattern
Here’s how to recall or save a pattern.
1.
Use the [BANK 1] [BANK 2] buttons to select a bank.
2.
Press one of the [OSC], [FIL], [ENV], [LFO], or [S1]–[S4] buttons to recall a pattern. By long-pressing
a button, you can save the pattern.
*
When you save a pattern, the newly-saved pattern overwrites the previously-saved pattern.
Step operations
Select a bank
Play/stop
1
[32]
[16]
[16T]
[8T]
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Using SEQ Mode
English
Owner’s Manual
CONTROLLER + GENERATOR
Copyright © 2015 ROLAND CORPORATION
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (leaet “USING THE UNIT SAFELY” and Owner’s Manual.)
After reading, keep the document(s) including those sections where it will be available for immediate reference.
The A-01 is a MIDI controller with two ribbon controllers and four rotary encoders. You can assign any MIDI messages to these controllers, and use them to control your DAW or external MIDI device. In addition,
the A-01 contains an 8-bit CPU sound module and a step sequencer, allowing you to also use it as a stand-alone synthesizer.
The A-01 also supports the Bluetooth® Smart standard, and can wirelessly exchange MIDI data with a mobile device such as a tablet or smartphone.
Introduction
Here’s how to make system settings for the A-01 and MIDI-related settings.
1.
Press the [MENU] button.
2.
Use the [H][I] buttons to select a parameter,
and use the [DEC] / [INC] buttons to specify
a value.
3.
When you have nished making settings,
press the [MENU] button to return to the
original mode.
Parameter list
SYSTEM parameter Value Explanation
Master Tune -64–63 Species the master tuning.
System Tempo 40-240
Species the basic tempo. If synchronization (slave) is disabled, the
tempo of the pattern will be the value that you specify here.
* When you change this value, the tempo of the currently-recalled
pattern also changes.
LCD Contrast 1–10
Adjusts the brightness of the display.
Auto O O, 30 min
Species the time after which the power automatically turns o if
the unit has not been operated.
* Auto O does not occur if the unit is USB-connected.
Eco Mode
O, 3 sec,
10 sec, 1 min
Species the time after which the display is dimmed if the unit has
not been operated.
Bluetooth LE O, On Turns Bluetooth communication on/o.
Bluetooth LE Name O, 1–9 Species the name that is displayed for the Bluetooth device.
Key Velocity
Species the velocity value that is transmitted when you play the
keyboard.
Touch
The transmitted velocity corresponds to the force with which you
play the key.
1–127
A xed velocity is always transmitted, regardless of the force with
which you play the key.
Velo Curve
Species the keyboard touch.
Light The keyboard feels light.
Normal The keyboard feels normal.
Heavy The keyboard feels heavy.
MIDI Clock
Auto
The tempo automatically synchronizes to MIDI clock (default).
Internal
The tempo specied on the A-01 unit is used. Choose the “Internal”
setting if you don’t want to synchronize to an external device.
CV Scale -63–+63 Adjusts the output scale of the CV signal.
CV Fine Tune -100–+100
Applies a ne adjustment to the output voltage of the CV signal.
CV Ref Note C0–C4
Species the note number (in steps of an octave) for which the
output of the CV OUT jack will be 0 V.
Bulk Dump
Execute, Cancel
Transmits controller settings, tones, and
patterns via MIDI.
Execute: [4] button
Cancel: [DEC] button
Factory Reset Resets the unit to the factory-set state.
PATCH parameter Value Explanation
Bank Select MSB 0–127 Species the bank select MSB value.
Bank Select LSB 0–127 Species the bank select LSB value.
Program Change 1–128 Species the program change value.
C1 Hold
O
On (hold value)
This setting species whether the value is held or returned to 0
when you release your nger from a ribbon controller (C1, C2).
C2 Hold
Note Scale 16 Types
Selects the scale (such as Chromatic or Major) that is used when
using the ribbon controller (C1) to play preview sounds.
Seq Tx Ch 1–16
Species the channel on which the MIDI messages of SEQ mode
(step sequencer) are transmitted.
Synth Ctrl Src
ALL, KEYBOARD,
16STEPSEQ,
MIDI ch 1–16
Selects the source that plays the synth.
CV/GATE Ctrl Src
Selects the signal that is output from the CV OUT jack and GATE
OUT jack.
CV Portamento SW
Applies a portamento eect to the CV signal.
O Portamento is not applied.
Always Portamento is always applied.
Legato Portamento is applied only when you play legato.
CV Portamento Time 1–127
Species the time of the portamento eect that is applied to the CV
signal. Higher values make the portamento apply more slowly.
CV Pitch Bend Range 1–12 Species the range of pitch bend in semitone units.
SysEX 1
Type:
Roland, Normal
Specify the system exclusive messages that are assigned to the
ribbon controllers (C1, C2) or encoders (R1–R4).
SysEX 2
SysEX 3
SysEX 4
System Settings
Memory
CONTROLLER mode:
16 patches (4 patches x 4 banks)
SYNTH mode:
16 tones (8 tones x 2 banks)
SEQ mode:
16 patterns (8 patterns x 2banks)
Power
Supply
Rechargeable Ni-MH battery (AA,
HR6) x 4, Alkaline battery (AA, LR6) x
4, USB bus power
Current
Draw
500 mA (USB bus power)
Dimensions
300 (W) x 128 (D) x 46 (H) mm
11-13/16 (W) x 5-1/16 (D) x 1-13/16 (H)
inches
Weight
950 g (including batteries)
2 lbs 2 oz
Accessories
Owner’s Manual, Leaet “USING THE
UNIT SAFELY,” Alkaline battery (AA,
LR6) x 4
Options
(sold
separately)
Keyboard unit: K-25m
* In the interest of product improvement, the specications and/or appearance of this unit are subject to change
without prior notice.
Main Specications
Roland A-01: CONTROLLER + GENERATOR
In SYNTH mode, the A-01 performs the functions that are printed below each operation button.
Creating a tone
1.
Press the button corresponding to the item (OSC, FIL, ENV, LFO) that you want to edit.
The parameters are displayed.
Button or encoder corresponding to the parameter for each item
S1 S2 S3 S4 R1 R2 R3 R4
OSC Saw Square
PWM
Noise
PW
Portamento
Portamento
Time
Octave
FIL Type1 Type2 Type3 OFF Cuto Resonance
Envelope
Mod
LFO Mod
ENV Envelope Gate — — Attack Decay Sustain Release
LFO Sine Square Saw Random LFO Mod LFO Rate LFO PWM (Zoom)
* PWM: Pulse Width Modulation, Mod: Modulation
2.
To edit a parameter, operate the button (S1–S4) or encoder (R1–R4) corresponding to that
parameter.
* Parameters that are assigned to the buttons (S1–S4) allow you to select one choice.
* In LFO, the Zoom parameter lets you change the magnication of the audio waveform.
3.
Repeat steps 1 and 2 to create your tone.
Recalling or saving a tone
Here’s how to recall or save a tone.
1.
Use the [BANK 1], [BANK 2] buttons to select a bank.
2.
Press one of the [OSC], [FIL], [ENV], [LFO], or [S1]–[S4] buttons to recall a tone. By long-pressing a
button, you can save the tone.
* When you save a tone, the newly-saved tone overwrites the previously-saved tone.
Performing
So that you can perform using the separately sold K-25m keyboard unit, the default settings assign
pitch bend to ribbon controller (C1) and modulation to ribbon controller (C2). By pressing the [
s
]
button you can play back the step sequencer.
Using SYNTH Mode
The A-01 has three modes: CONTROLLER, SYNTH, and
SEQ. Press the [MODE] button to switch between these
modes.
7
CONTROLLER Mode
In CONTROLLER mode you use the two ribbon controllers (C1, C2) and four encoders to control your
MIDI equipment. The assignments of each controller can be saved in buttons [1]–[4].
7
SYNTH Mode
In SYNTH mode you can create sound by editing the settings of the oscillator, lter, envelope, and
LFO. You can save up to 16 of the sounds (tones) that you create (8 tones x 2 banks).
7
SEQ (Step Sequencer) Mode
The A-01 operates as a 16-step step sequencer, allowing you to view and edit the steps in four
blocks each containing four steps.
Switching the Mode (CONTROLLER / SYNTH / SEQ)
In CONTROLLER mode, the A-01 performs the functions that are printed above each operation button.
Editing the settings
To edit the settings, use the [
C
] [
A
] [
=
] [
?
] buttons
to move to an item, and use the [INC] [DEC] buttons to
edit the parameter.
Recalling and saving a patch
You can recall or save controller settings for the patch as follows. Up to 16 sets of patches (4 patches × 4
banks) can be saved.
1.
Hold down the [?] button and use the [1]–[4] buttons to select a bank.
2.
Press one of the [1]–[4] buttons to recall a patch. If you long-press a button, the current settings
are saved in that number.
* When you save the settings, the previously-saved settings are overwritten by the newly-saved
settings.
The parameter you’re editing
Using CONTROLLER Mode
The A-01 operates on batteries or on USB bus power. If using the unit on batteries, install four AA
batteries, ensuring that the batteries are oriented correctly.
* When the batteries run low, the LED at the top of ribbon controller (C1) blinks. Please install new
batteries.
* If you handle batteries improperly, you risk explosion and uid leakage.
* This unit is equipped with a protection circuit. A brief interval (a few seconds) after turning the
unit on is required before it will operate normally.
* The power to this unit will be turned o automatically after a predetermined amount of time has
passed since it was last used for playing music, or its buttons or controls were operated (Auto O
function). If you do not want the power to be turned o automatically, disengage the Auto O
function.
• Any settings that you are in the process of editing will be lost when the power is turned o. If
you have any settings that you want to keep, you should save them beforehand.
• To restore power, turn the power on again.
Important Notes
Switching between modes
CONTROLLER
SYNTH SEQ

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Roland A-01 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Roland A-01

Roland A-01 Bedienungsanleitung - Deutsch - 1 seiten

Roland A-01 Bedienungsanleitung - Holländisch - 1 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info