Bedienungsanleitung Roland AT 800 (Seite 7 von 292) (Englisch)

527368

Zoom out

Zoom in

Vorherige Seite

1/292

Nächste Seite

Important Notes

566b

• The sensitivity of the D Beam controller will change depending

on the amount of light in the vicinity of the unit. If it does not

function as you expect, adjust the sensitivity as appropriate for

the brightness of your location.

Add

• In order to provide the highest possible image quality, the

ATELIER uses a TFT liquid crystal display. Due to the nature of

a TFT liquid crystal display, the screen may contain pixels that

fail to light or that remain constantly lit, but please be aware

that this is not a malfunction or defect.

Floppy Disk Handling

(Using Optional Floppy Disk Drive)

651

• Floppy disks contain a plastic disk with a thin coating of

magnetic storage medium. Microscopic precision is required

to enable storage of large amounts of data on such a small

surface area. To preserve their integrity, please observe the

following when handling floppy disks:

• Never touch the magnetic medium inside the disk.

• Do not use or store floppy disks in dirty or dusty areas.

• Do not subject floppy disks to temperature extremes

(e.g., direct sunlight in an enclosed vehicle).

Recommended temperature range: 10–50 degrees C

(50–122 degrees F).

• Do not expose floppy disks to strong magnetic fields,

such as those generated by loudspeakers.

652

• Floppy disks have a “write protect” tab which can protect the

disk from accidental erasure. It is recommended that the tab

be kept in the PROTECT position, and moved to the WRITE

position only when you wish to write new data onto the disk.

fig.DiskProtect.e.eps

653

• The identification label should be firmly affixed to the disk.

Should the label come loose while the disk is in the drive, it

may be difficult to remove the disk.

654

• Store all disks in a safe place to avoid damaging them, and to

protect them from dust, dirt, and other hazards. By using a

dirty or dust-ridden disk, you risk damaging the disk, as well

as causing the disk drive to malfunction.

USB Memory Handling

704

• When connecting USB memory, firmly insert it all the way in.

705

• Do not touch the pins of the USB memory connector, or allow

them to become dirty.

708

• USB memory is made using high-precision electronic

components, so please observe the following points when

handling it.

• To prevent damage from static electrical charges,

discharge any static electricity that might be present in

your body before handling USB memory.

• Do not touch the terminals with your fingers or any metal

object.

• Do not bend or drop USB memory, or subject it to strong

impact.

• Do not leave USB memory in direct sunlight or in

locations such as a closed-up automobile. (Storage

temperature: 0–50 degrees C)

• Do not allow USB memory to become wet.

• Do not disassemble or modify USB memory.

Addition

• When connecting USB memory, position it horizontally with

the external memory connector and insert it without using

excessive force. The external memory connector may be

damaged if you use excessive force when inserting USB

memory.

Addition

• Do not insert anything other than USB memory (e.g., wire,

coins, other types of device) into the external memory

connector. Doing so will damage the external memory

connector.

Addition

• Do not apply excessive force to the connected USB memory.

Addition

• If you will not be using USB memory for an extended period of

time, close the USB memory cover.

Handling the CDs (CD-ROMs)

Add

• When handling the discs, please observe the following.

• Do not touch the encoded surface of the disc.

• Do not use in dusty areas.

• Do not leave the disc in direct sunlight or an enclosed

vehicle.

801

• Avoid touching or scratching the shiny underside (encoded

surface) of the disc. Damaged or dirty CD-ROM discs may not

be read properly. Keep your discs clean using a commercially

available CD cleaner.

Add

• Keep the disc in the case.

Add

• Do not keep the disc in the CD drive for a long time.

Add

• Do not put a sticker on the label of the disc.

Add

• Wipe the disc with a soft and dry cloth radially from inside to

outside. Do not wipe along circumference.

Add

• Do not use benzine, record cleaner spray or solvents of any

kind.

Add

• Do not bend the disc. Bending discs may prevent proper

reading and writing of data, and may further result in

malfunction.

852

• This product can be used to record or duplicate audio or

visual material without being limited by certain technological

copy-protection measures. This is due to the fact that this

product is intended to be used for the purpose of producing

original music or video material, and is therefore designed so

that material that does not infringe copyrights belonging to

others (for example, your own original works) can be

recorded or duplicated freely.

853

• Do not use this unit for purposes that could infringe on a

whatsoever with regard to any infringements of third-party

copyrights arising through your use of this unit.

Rear side of the disk

Write

(can write new data onto disk)

Protect

(prevents writing to disk)

Write Protect Tab

AT-800_e.book 7 ページ２００８年１０月１５日　水曜日　午前９時３７分

Roland AT 800 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland AT 800

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info