Bedienungsanleitung Roland AT 900C (Seite 278 von 308) (Englisch)

527370

278

Zoom out

Zoom in

Vorherige Seite

1/308

Nächste Seite

276

Troubleshooting

Problems with the Sound

Problem

Check Solution Page

The volume level of the instrument

connected to ATELIER is too low.

Could you be using a connection cable

that contains a resistor?

Use a connection cable that does not

contain a resistor.

p. 245

Noise is heard in the sound

If there is a cell phone nearby, you

may hear noise from the ATELIER when

an incoming call or outgoing call

occurs, or during a conversation.

Keep the phone as far away as

possible, or turn off its power.

- - -

When the human voice “Jazz Scat” is

selected, playing dynamics do not

change the sound

The setting of “Initial Touch” is turned

OFF.

Turn “Initial Touch” on.

p. 212

Rotary effect is not be applied

Some sounds do not allow the rotary

effect to be applied.

This is not a malfunction.

- - -

Chorus effect does not apply

Some sounds do not allow the chorus

effect to be applied.

This is not a malfunction.

- - -

When you release your fingers from

keys in the Lower keyboard, the

notes continue sounding

The Lower Voice [Hold] button is at

ON.

Press the Lower Voice [Hold] button to

turn it off (dark).

p. 82

Sound is produced when you take

your finger off a key

You have selected a “Marimba Treml”

or “Banjo Treml” sound.

If you select a “Marimba Treml” or

“Banjo Treml” sound, a sound will also

be produced when you take your

finger off the key.

This is not a malfunction.

- - -

Some keys (of certain keyboard

parts) sound strange

You are playing notes outside the

recommended range of the voice.

This is not a malfunction.

- - -

Bass is heard even though you are

not playing the Bass Pedalboard

The Pedal [To Lower] button or the

[Bass Split] button is ON.

When the Pedal [To Lower] button is

ON, the Bass will be sounded by the

Lower keyboard.

In the Pedal part, press the Pedal [To

Lower] button or [Bass Split] button to

turn the button off (dark).

p. 163

p. 165

When playing the same sound in the

Upper keyboard and Lower

keyboard, the volume is different

On one of the keyboards, “Initial

Touch” is turned ON.

Set the initial touch settings of the

Upper keyboard and the Lower

keyboard to both On, or both Off.

p. 212

The sound is not played correctly

If you layer the same type of sound (for

example, Strings 1 and Strings 5), or

play an octave-shifted organ sound,

the timing at which you play a note or

the phase relationship between the two

sounds may affect the way in which the

sounds are heard, but this is not a

malfunction.

You are layering sounds of the same

type (e.g., Strings 1 and Strings 5).

Alternatively, you are playing an

organ sound with Octave Shift.

This is not a malfunction.

- - -

AT-900_e.book 276 ページ２００８年９月１６日　火曜日　午前１０時３８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland AT 900C Seite 278

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland AT 900C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info