527334
102
Zoom out
Zoom in
Vorherige Seite
1/148
Nächste Seite
100
Record and Playback Your Performance
4.
Press the Value [-] or [+] button to select the
SMF music files that you wish to load into
internal memory.
5.
Press the [Load] button.
The selected performance data will be loaded into
internal memory.
6.
Press the [Bwd] button and the [Fwd] buttons
to select the desired measure (bar) when you
start recording.
If you wish to start recording from the beginning of the
song, press the [Reset] button.
7.
Select the panel settings needed for recording
the performance.
8.
Press the [Rec] button to enter recording-
standby mode.
The [Rec] button indicator will light, and the [Play/Stop]
button and the unrecorded track buttons will blink. The
track buttons that are already recorded will light.
9.
Press the button of the track you want to
record, so it’s blinking.
The existing performance data in the specified track will
be erased as recording takes place.
When the button for a track lights steadily, it means it won’t
be recorded.
10.
Press the [Play/Stop] button to start recording.
During recording, the performance data that was loaded
into the ATELIER will play back.
11.
Press [Stop] button to stop recording.
The track button for which performance data has been
recorded will be lit.
The performance data you recorded can be saved on a USB
memory, “Favorites,” or floppy disk (p. 96).
Commercially sold music files can also be loaded into the
ATELIER, but for reasons of copyright protection, cannot be
saved in SMF format.
The performances of Channel 2 in SMF music files are
deleted when pedal performances are recorded over again.
1.
Prepare the performance data whose tempo
you want to change.
If you’re using performance data from USB memory,
connect it to the external memory connector.
If you’re using performance data from a floppy disk,
connect the floppy disk drive to the external memory
connector, and insert the floppy disk.
2.
Load the performance data into the ATELIER
(p. 97)
.
3.
Determine the tempo with the Tempo [ ] and
[ ] buttons.
4.
Hold down the panel [Reset] button and press
the [Rec] button.
The tempo of the performance data will change.
NOTE
NOTE
NOTE
Using Song with a Different Tempo
Than That of the Performance Song
3
64
3
AT-100-300_e.book 100 ページ 2008年5月7日 水曜日 午後3時33分
102

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Roland AT300 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Roland AT300

Roland AT300 Bedienungsanleitung - Holländisch - 144 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info