Bedienungsanleitung Roland Blues Cube Stage (Seite 11 von 19) (Englisch)

708969

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Deutsch

Français Italiano Español PortuguêsEnglish Nederlands

English

Panel Descriptions

10 FOOT SWITCH

TIP: CH SELECT RING: DUAL TONE jack

If a footswitch (sold separately: BOSS FS-6, FS-7, or FS-5L) is

connected, you can use it to switch between the CLEAN/CRUNCH

channels, or to turn DUAL TONE (p. 6) on/o.

For detail, refer to “Connecting a Footswitch (FS-6/FS-7/FS-5L)” (p. 10).

TIP: TREMOLO RING: EFX LOOP jack

Artist only

If a footswitch (sold separately: BOSS FS-6, FS-7, or FS-5L) is

connected, you can use it to turn the tremolo eect on/o or to

turn on/o the eect of the unit that’s connected to the eect loop.

For detail, refer to “Connecting a Footswitch (FS-6/FS-7/FS-5L)” (p. 10).

TIP: EFX LOOP A: EFX LOOP B jack

Tour only

If a footswitch (sold separately: BOSS FS-6, FS-7, or FS-5L) is

connected, you can use it to turn on/o the eect of the unit that’s

connected to the Eect Loop A/B.

For detail, refer to “Connecting a Footswitch (FS-6/FS-7/FS-5L)” (p. 10).

GA-FC jack

Artist/Tour only

You can connect a separately sold Roland GA-FC and use it to

switch channels or turn DUAL TONE, TREMOLO, and EFX LOOP on/

o (TREMOLO is available on the Blues Cube Artist only).

For detail, refer to ”Connecting a GA Foot Controller (sold

separately: GA-FC)” (p. 10).

11 REC OUT O port

You can use a commercially available USB 2.0 cable to record the

sound of the Blues Cube into your computer.

You must install the USB driver before connecting the unit to

your computer.

Download the USB driver from the Roland website. For details, refer

to Readme.htm which is included in the download.

http: //www.roland.com/support/

12 PHONES jack

Connect headphones here. You can obtain powerful guitar sounds

just as if you were playing through the speaker. To adjust the

volume, use the [VOLUME] knob of the CLEAN channel or the

CRUNCH channel, along with the [MASTER] knob.

* If a plug is inserted in this jack, no sound will be output from

the Blues Cube’s own speaker. This is convenient if you don’t

want loud sound to be produced from the speaker, such as

when you’re practicing at night.

13 LINE OUT

LINE OUT jack

Connect this to your PA system or recorder. You can obtain powerful

guitar amp sound just as if you were playing through the speaker.

Recorder, etc.

You can use this in conjunction with an external PA system, or to

record your performance via direct line while monitoring the sound

from the Blues Cube’s speaker.

Adjust the output level using the [VOLUME] knob of the CLEAN

channel or the CRUNCH channel.

* The Blues Cube Tour is equipped with

balanced (XLR) type jacks. Wiring

diagrams for these jacks are shown

below. Make connections after rst

checking the wiring diagrams of

other equipment you intend to

connect.

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

[GND LIFT] switch

Tour only

Loop hum noise may occur when other external devices are

connected to the Blues Cube Tour. In such instances, you may be

able to mitigate the problem by switching the position of the [GND

LIFT] switch. The [GND LIFT] switch should be normally set to OFF.

Switch Description

ON Pin 1 is disconnected from the Blues Cube Tour’s ground.

OFF Pin 1 connects to the Blues Cube Tour’s ground.

14 EFX LOOP SEND/RETURN jacks

Artist/Tour only

Connect an external eect device (monaural).

Connect the SEND jack to the input of your external eect device,

and connect the output of your external eect device to the

RETURN jack.

External eects unit

OUTPUTINPUT

Artist only

The EFX LOOP of the Blues Cube Artist is a series

loop. If the volume of your external eect device is turned down

or if it is powered-o, there will be no sound.

Tour only

On the Blues Cube Tour, you can press the front

panel [EFX LOOP A/EFX LOOP B] buttons simultaneously to

switch between a series loop and a parallel loop (which mixes

the guitar sound of this unit with the sound of your external

eect device).

15 SPEAKER OUT jack

Tour only

Connect a speaker box (separately sold; e.g., the BC-CAB410).

* Only use speaker cable to connect the speaker. Do not use any

shielded cable designed for use with guitars.

[IMP. SELECT] (Impedance Select) switch

Make settings as appropriate for the specications of the speaker

box that you connect. For details, refer to the owner's manual of

your speaker box.

If you connect the BC-CAB410 (separately sold), set this to 4 Ω.

16 MIDI IN jack

Tour only

You can control the Blues Cube Tour from a multi-eect unit or a

MIDI foot controller.

1:GND 2:HOT

3:COLD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland Blues Cube Stage Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland Blues Cube Stage

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info