Bedienungsanleitung Roland CD-2I (Seite 130 von 144) (Englisch)

527442

130

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

130

Troubleshooting

(continued)

Problems with the Sound

(continued)

Problem

Cause and Action

See

Page

The sound recorded via

the internal mics is not

loud enough

●

Have you adjusted the input level of the internal mics?

➔

Turn the [MIC] knob to raise the input level of the internal mics.

The recorded sound is

noisy or distorted

●

Is the input level adjusted appropriately?

➔

Noise can tend to be become more noticeable if the sound being input

is at a relatively low level. On the other hand, distortion can crop up

when the level is high. Try to always keep the input level adjusted to a

setting that's appropriately matched to the volume of the sound you're

inputting.

➔

If you raise the input level when you're using a record player or an

external microphone with limited sensitivity, any noise from the internal

CD drive could become more noticeable and might be recorded along

with your recording. If you feel dissatisfied with the outcome, try using

the following procedure when recording.

Use batteries to power the unit. (23)

Record to SD memory card. (44, 49, 52, 55)

Use the AC adaptor to power the unit. (21)

Write the song data on the SD memory card to a CD. (97)

➔

Adjust the input level so that the PEAK indicator lights briefly when loud

sounds are input.

41, 45,

50, 56

●

Could the input level be raised for a jack to which no device is

connected?

➔

Even if no device is connected, we recommend that you turn down the

input level—turn the knob all the way to the left—for everything other

than the audio source you’re recording.

—

●

Could MIC SELECT be set to “Internal

”

➔

Even though you thought you were recording using an external mic, a

noisy recording may indicate that you were actually recording through

the internal mics. If you want to record using an external mic, set to the

“EXT.”

●

Is the output level set correctly?

➔

If you raise the output level too high, noise or distortion may occur in

the sound from the internal speakers. Turn the [OUTPUT LEVEL] knob to

adjust the volume.

Unintended tone quality

●

Could you have made bass or treble settings?

➔

Set the bass and treble settings to “0.”

An unwanted effect is

applied to the sound

●

Could you have selected a reverb?

➔

Turn the reverb “Off.”

Volume changes are not

recorded correctly

according to the actual

performance

●

Could the [MIC LEVEL] switch be set to the “AUTO” position?

➔

The “AUTO” position is suitable for recording human voices at a

meeting or lecture, and may be unsuitable for recording an instrumental

performance. Change the setting to “MANUAL,” and turn the [MIC]

knob to adjust the input level.

CD-2i_e.book 130 ページ２０１０年３月１５日　月曜日　午前１０時１５分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland CD-2I Seite 130

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland CD-2I

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info