Bedienungsanleitung Roland CDX-1 (Seite 14 von 252) (Englisch)

527761

Zoom out

Zoom in

Vorherige Seite

1/252

Nächste Seite

Expanding the memory

The CDX-1 comes with 32 MB of memory into which audio samples can be loaded.

However, in some cases, 32 MB of memory will be insufficient for loading large

amounts of data. In such a case, you will have to add separately sold memory

(DIMM). Memory can be expanded up to 128 MB.

Before expanding the memory, consult with your retailer, the nearest Roland Service

Center, or an authorized Roland distributor.

Precautions for expanding memory

• Always turn the unit off and unplug the AC adaptor before attempting

installation of the memory DIMM board.

• Install only the specified memory DIMM board. Remove only the

specified screws.

• To avoid the risk of damage to internal components that can be caused by static

electricity, please carefully observe the following whenever you handle the

board.

❍ Before you touch the board, always first grasp a metal object (such as a water

pipe), so you are sure that any static electricity you might have been carrying

has been discharged.

❍ When handling the board, grasp it only by its edges. Avoid touching any of

the electronic components or connectors.

❍ Save the bag in which the board was originally shipped, and put the board

back into it whenever you need to store or transport it.

• Do not touch any of the printed circuit pathways or connection terminals.

• Never use excessive force when installing a circuit board. If it doesn’t fit

properly on the first attempt, remove the board and try again.

• When circuit board installation is complete, double-check your work.

• When turning the unit upside-down, get a bunch of newspapers or magazines,

and place them under the four corners or at both ends to prevent damage to the

buttons and controls. Also, you should try to orient the unit so no buttons or

controls get damaged.

• When turning the unit upside-down, handle with care to avoid dropping it, or

allowing it to fall or tip over.

• Use a Philips screwdriver of the appropriate size to avoid damaging the screw

heads (a number of 2 screwdriver). If an unsuitable screwdriver is used, the

head of the screw may be stripped.

• Turn the screwdriver counter-clockwise to loosen the

screws-turn it clockwise to tighten them.

• Be careful not to cut your hand on the edge of the cover or the opening edge

while removing the cover.

• Be careful not to let the screws drop inside the CDX-1's body.

• Do not touch the circuitry or the connectors.

• Do not force a memory board into its slot. If it can't be inserted smoothly, take it

out, check its orientation and try again.

If you add 128 MB of

separately sold memory, the

standard 32 MB of memory

will no longer be used.

In case of expanding memory

other than 128 MB of memory,

turn on the power, a message

“Wrong DIMM Type! Turn off

the power, and replace

w/correct one” appears, and.

At this time, the CDX-1 will

not operate normally.

tightenloosen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland CDX-1 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland CDX-1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info