Bedienungsanleitung Roland CM-30 (Seite 7 von 16) (Englisch)

527768

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Panel Descriptions

1. CH 1 knob / CH 1 Input Jacks

In addition to a 1/4” phone jack, this channel is

equipped with a balanced XLR connector, useful

for connecting microphones.

This accepts input levels ranging from mic input

(-50 dBu) to line level from sound modules and

other equipment (-20 dBu).

* The pin assignment for the XLR type connectors is as

shown below. Before making any connections, make sure

that this pin assignment is compatible with that of all

your other devices.

fig.04

2. CH 2 and CH 3 knobs / CH 2 and CH

3 Input Jacks

Use these for connecting keyboards, sound

modules, and other devices.

You can make stereo connections to these inputs.

If you connect only the L jack, the input will be

mono.

If you’re using stereo connections, you can listen

in stereo through headphones or when using a

pair of stereo-linked CM-30 speakers.

They accept line level input (-20 dBu).

3. STEREO PHONES

The headphones allow you to listen in stereo.

LEVEL Knob

This knob adjusts the headphones volume.

PHONES Jack

This is for connecting headphones.

* Before plugging in or unplugging headphones, be sure to

place the LEVEL knob at 0.

4. EQUALIZER

LOW Knob

This adjusts the level of the bass range.

HIGH Knob

This adjusts the level of the treble range.

5. MASTER Knob

This adjusts the total volume level of the unit’s

internal speaker.

6. Power Indicator

This indicator illuminates when the power is on.

7. POWER Switch

This switches the power on and off.

* Always be sure to lower the MASTER knob on the CM-

30 to 0 whenever turning the power on or off.

* This unit is equipped with a protection circuit. A brief

interval (a few seconds) after power up is required before

the unit will operate normally.

Slight pop noise may come from the speakers when the

power is switched on, but this does not indicate a

problem.

* Refer to p. 9 for the order in which to turn the power to

connected devices on and off.

8. AUX IN 1, 2 Jacks

AUX IN 1 are RCA phono type input jacks. AUX

IN 2 is stereo miniature phone type input jack.

You use these to connect equipment such as CD

and MD players, and have them sound along

with the equipment connected to CH 1 through

CH 3.

Both AUX IN 1 and 2 accept level input of -10

dBu.

* To adjust the volume level of equipment connected to the

AUX IN jacks, use the controls on such equipment.

9. STEREO LINK

Stereo playback is enabled simply by connecting

two CM-30 units with a single or double audio

cables (phone type).

* For details on the Stereo Link function, refer to “Using

Two CM-30 Speakers for Stereo Playback (Stereo Link)”

(p. 10).

They provide -10 dBu line level output, and

accept level input of -10 dBu.

10. AC IN Jack

Connect the included power cord to this jack.

* Use only the power cord included with the CM-30.

CM-30_e.book 7 ページ２００４年７月２８日　水曜日　午前９時３２分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland CM-30 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland CM-30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info