Bedienungsanleitung Roland CUBE 120XL BASS (Seite 15 von 42) (Deutsch, Englisch)

527435

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Português Italiano DeutschNederlands Español Français

English

You can save and call up the panel settings (those enclosed by the line

in the gure) for sounds you create. On this unit, this function is called

“SOLO.” This is a convenient way to switch between a backing sound

and a solo sound.

With the factory settings, the sample setting “HEAVY BOTTOM” (p. 16) is

saved.

CUBE-60XL BASS

CUBE-120XL BASS

Saving the Panel Settings

1. Set the SOLO [VOLUME] knob to 0.

NOTE

If the SOLO volume is set high, the

sound may be unexpectedly loud

when the panel settings are saved.

Before saving, lower the volume to 0.

2. Create a sound.

3. Press and hold the SOLO [ON/OFF] switch on the panel for

several seconds.

The indicator will blink. When the panel settings

have been saved, the indicator will change from

blinking to lit.

* Never switch o the power while the indicator

is blinking.

4. Use the SOLO [VOLUME] knob to adjust

the volume.

* Saved panel settings remain in memory even after the power is

turned o.

Recalling the Saved Sound

1. With SOLO o, press the SOLO [ON/OFF] switch.

The SOLO indicator will light, and the saved panel settings will be

recalled.

* If you’re using the CUBE for the rst time, the factory settings will be

recalled.

Editing the saved settings

1. Press the SOLO [ON/OFF] switch to call up the saved settings.

2. Turn the panel knob for the item you want to change, and

modify the setting.

The SOLO indicator goes out briey when the position of the knob

coincides with the position stored in memory.

3. Hold down the SOLO [ON/OFF] switch for several seconds.

The indicator will blink. When the panel settings have been saved, the

indicator will change from blinking to lit.

* Never switch o the power while the indicator is blinking.

* Once the new settings have been saved, the previous settings in

eect before the changes cannot be called up again.

* To quit without saving the changes, press the SOLO [ON/OFF]

switch.

Note the following if you’ve set FOOT SW

TYPE to FS-5L (LATCH)

• If a foot switch is connected to the SOLO/COMP/DRIVE jack, the

SOLO [ON/OFF] switch will be inoperable.

• If SOLO is on, and a foot switch is connected to the SOLO/COMP/

DRIVE, EFX/REVERB or DELAY/REC/PLAY/DUB/TAP/STOP jack, the

foot switch’s indicator may not match the on/o status of the CUBE’s

COMP/DRIVE, EFX, REVERB, or DELAY. If you want the on/o status

of the CUBE’s COMP/DRIVE, EFX, REVERB, or DELAY to consistently

conform to the foot switch’s indicator, change the setting for the

CUBE-60XL BASS/CUBE-120XL BASS to “Foot Switch Priority Mode. ”

For details, see ”Using a Latch-type Foot Switch” (p. 11).

• In order to be able to save the panel settings, you rst need to

switch on SOLO using the foot switch.

Returning to the Factory-default Settings

Hold down the [TAP/STOP] switch and the SOLO [ON/OFF]

switch at the same time and switch on the power. The SOLO

indicator blinks and the settings saved with the SOLO function

are returned to their factory defaults.

Using the SOLO Function

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland CUBE 120XL BASS Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland CUBE 120XL BASS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info