Bedienungsanleitung Roland D-2 GROOVEBOX (Seite 99 von 115) (Deutsch)

527871

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

MIDI-Implementation

Anhang

● Program Change

status 2nd byte

CnH ppH

pp=Program number: 00H–7FH (prog.1–prog.128)

●Channel Aftertouch

status 2nd byte

DnH vvH

* The effect will apply according to the Aftertouch Control setting.

●Pitch Bend Change

status 2nd byte 3rd byte

EnH llH mmH

mm,ll=Pitch Bend value:00 00H–40 00H–7F 7FH (-8192–0–+8191)

* The effect will apply according to the Pitch Bend Control setting.

■Channel Mode messages

●All Sound Off (Controller number 120)

status 2nd byte 3rd byte

BnH 78H 00H

* When this message is received, all notes currently sounding on the corresponding

channel will be turned off.

●Reset All Controllers (Controller number 121)

status 2nd byte 3rd byte

BnH 79H 00H

* When this message is received, the following controllers will be set to their reset values.

Controller Reset value

Pitch Bend Change ±0 (center)

Polyphonic Key Pressure 0 (off)

Channel Pressure 0 (off)

Modulation 0 (off)

Expression 127 (maximum)

Hold 1 0 (off)

Sostenuto 0 (off)

Soft 0 (off)

Hold 2 0 (off)

RPN Unset. Previously set data will not change.

●All Note Off (Controller number 123)

status 2nd byte 3rd byte

BnH 7BH 00H

* When All Note Off is received, all currently sounding notes of the corresponding

channel will be turned off. However if Hold 1 or Sostenuto are on, the sound will be held

until these are turned off.

●Omni Off (Controller number 124)

status 2nd byte 3rd byte

BnH 7CH 00H

* The same processing as when All Note Off is received will be done.

●Omni On (Controller number 125)

status 2nd byte 3rd byte

BnH 7DH 00H

* The same processing as when All Note Off is received will be done. The instrument will

not be set to OMNI ON.

●Mono (Controller number 126)

status 2nd byte 3rd byte

BnH 7EH mmH

mm=Mono number: 00H–10H (0–16)

* The same processing as when All Note Off is received will be done, and the Solo Switch

parameter will be set to ON.

●Poly (Controller number 127)

status 2nd byte 3rd byte

BnH 7FH 00H

* The same processing as when All Note Off is received will be done, and the Solo Switch

parameter will be set to OFF.

■System Realtime messages

●Timing Clock

status

F8H

* Settings can be made to synchronize or the LFO rate or the effect rate.

●Active Sensing

status

FEH

* When an Active Sensing message is received, the unit will begin monitoring the interval

at which MIDI messages are received. During monitoring, if more than 420 ms passes

without a message being received, the same processing will be done as when All Sound

Off, All Note Off, and Reset All Controllers messages are received. Then monitoring will

be halted.

■ System Exclusive messages

status data byte status

F0H iiH, ddH, ......, eeH F7H

F0H: System Exclusive message status

ii = ID number: This is the ID number (manufacturer ID) that specifies the

manufacturer whose exclusive message this is. Roland’s manufacturer

ID is 41H.ID numbers 7EH and 7FH are defined in an expansion of the

MIDI standard as Universal Non-realtime messages (7EH) and

Universal Realtime Messages (7FH).

dd,..., ee = data: 00H–7FH (0–127)

F7H: EOX (End Of Exclusive) This is the last status of system exclusive

message.

●Universal Non-realtime System Exclusive Messages

IdentityIdentity Request Message

Status Data byte Status

F0H 7EH, dev, 06H, 01H F7H

Byte Explanation

F0H Exclusive status

7EH ID number (universal non-realtime message)

dev Device ID (dev:10H(17)-1FH(32))

06H Sub ID#1 (General Information)

01H Sub ID#2 (Identity Request)

F7H EOX (End Of Exclusive)

* The “dev” is own device number or 7FH (Broadcast)

* When Identity Request is received, Identity Reply message will be transmitted.

●Data Request 1 RQ1

This message requests the other device to transmit data. The address and size indicate the

type and amount of data that is requested.

When a Data Request message is received, if the device is in a state in which it is able to

transmit data, and if the address and size are appropriate, the requested data is transmitted

as a Data Set 1 (DT1) message. If the conditions are not met, nothing is transmitted.

The model ID of the exclusive messages used by this instrument is 00 0BH.

status data byte status

F0H 41H, dev, 00H, 0BH, 11H, aaH, bbH, F7H

ccH, ddH, ssH, ttH, uuH, vvH, sum

Byte Remarks

F0H Exclusive status

41H ID number (Roland)

dev device ID (dev: 10H–1FH)

00H model ID (D2)

0BH model ID (D2)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland D-2 GROOVEBOX Seite 99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland D-2 GROOVEBOX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info