• Do not allow rubber, vinyl, or similar materials
to remain on this product for long periods of
time. Such objects can discolor or otherwise
harmfully a ect the nish.
• Depending on the material and temperature of
the surface on which you place the product, its
rubber feet may discolor or mar the surface.
As a precautionary measure, we recommend
the use of a drum mat.
• Do not put anything that contains water on
this product. Also, avoid the use of insecticides,
perfumes, alcohol, nail polish, spray cans, etc.,
near the product. Swiftly wipe away any liquid
that spills on the product using a dry, soft cloth.
Maintenance
• For everyday cleaning wipe the product with
a soft, dry cloth or one that has been slightly
dampened with water. To remove stubborn
dirt, use a cloth impregnated with a mild, non-
abrasive detergent. Afterwards, be sure to wipe
the product thoroughly with a soft, dry cloth.
• Never use benzine, thinners, alcohol or
solvents of any kind, to avoid the possibility of
discoloration and/or deformation.
WARNING
Do not disassemble or modify by yourself
Do not open or perform any internal
modi cations on the product. (The
only exception would be where this
manual provides speci c instructions
which should be followed in order to put in place
user-installable options.)
Do not repair or replace parts by yourself
Do not attempt to repair the product,
or replace parts within it (except
when this manual provides speci c
instructions directing you to do so).
Refer all servicing to your retailer, the nearest
Roland Service Center, or an authorized Roland
distributor, as listed on the “Information.”
Do not use or store in the following types of locations
• Subject to temperature extremes
(e.g., direct sunlight in an enclosed
vehicle, near a heating duct, on top of
heat-generating equipment); or are
• Damp (e.g., baths, washrooms, on
wet oors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Humid; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and
shakiness.
Do not place in an unstable location
Make sure you always have the product
placed so it is level and sure to remain
stable. Never place it on stands that
could wobble, or on inclined surfaces.
WARNING
Adults must provide supervision in places where
children are present
When using the product in locations
where children are present, be careful
so no mishandling of the product can
take place. An adult should always be
on hand to provide supervision and guidance.
Do not drop or subject to strong impact
Protect the product from strong
impact.
(Do not drop it!)
CAUTION
Avoid climbing on top of the product, or placing heavy
objects on it
Never climb on top of, nor place heavy
objects on the product.
Take care not to get ngers pinched by moving parts
Take care not to pinch your ngers
or other parts of your body when
operating the moving parts of the
pedal or drum throne. If small children
use this equipment, make sure they have adult
supervision and guidance.
Keep small items out of the reach of children
Keep removable parts (screws, nuts,
memory lock) out of the reach of small
children to prevent them from being
swallowed accidentally.
1. Open the tripod
Loosen wing bolt “B” and open the tripod all the way to the stopper.
When the tripod is fully open, rmly fasten wing bolt “B,” which you
loosened earlier.
Wing bolt “B”
2. Attach the seat
Loosen wing bolt “A,” raise the upper
pipe to the desired height, and
provisionally tighten wing bolt “A,” so
that the upper pipe does not drop.
Next, use the drum key to loosen
the square-head bolt of the memory
lock, and lower the memory lock to
the position shown in the illustration
below.
Attach the seat, and tighten the T-bolt
to fasten it securely.
3. Adjust the height of the seat
Loosen wing bolt “A” and adjust the throne to the desired height.
When you’ve adjusted the height as desired, securely tighten wing bolt
“A.” Next, align the memory lock to the position shown in the illustration
below, and securely tighten the square-head bolt of the memory lock
to fasten it.
* Using the memory lock will prevent the seat from descending
during performance.
Square-head
bolt of the
memory lock
Wing bolt
“A”
Drumsticks
Use the drumsticks to play the V-Drums.
Upper pipe
Wing bolt “A”
Square-head bolt of
the memory lock
Kick Pedal
Beater
Square-Head bolt “A”
Foot board
Beater holder
Square-Head bolt “B”
Angle adjuster
Roller
Spring
Lock nut
Adjusting nutHoop clamp
Assembling the Kick Pedal
Before using this product, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES”.
These sections provide important information concerning the proper operation of the product. Additionally, in order to feel assured that you have gained a good grasp of
every feature provided by your new product, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.
1. Attach the beater
Use the drum key to loosen square-head bolt “A.” Next, insert the beater
into the beater holder with the prastic beater facing the head, as shown
in the illustration below. Then, secure it by tightening square-head bolt
“A,” which you loosened earlier.
Square-Head
bolt “A”
Plastic beater
NOTE
The mesh head can wear down a felt beater. We recommend using a
plastic beater.
2. Attach to the V-Drums kick pad
Insert the kick pad’s pedal attachment plate into the hoop clamp of the
kick pedal, and fasten it.
* For details, refer to the owner’s manual of the V-Drums kick pad.
3. Adjust the angle of the beater
Loosen square-head bolt “B” and adjust the beater to the desired angle.
When you’ve set the angle, rmly tighten square-head bolt “B” to secure
it.
Square-Head
bolt “B”
4. Adjust the spring
Loosen the adjusting nut to adjust the tension of the spring.
Once you’ve got the tension adjusted to your liking, rmly secure the lock
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Roland DAP-3X wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
