Bedienungsanleitung Roland DJ-202 (Seite 15 von 17) (Englisch)

710369

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

System Settings

1. While holding down the [LOAD] button at the right side (R channel) of the browser section, use a USB cable to connect the DJ-202 to

your computer; continue holding down the [LOAD] button until the SEQUENCER section’s [START/STOP] button blinks.

The DJ-202 is in system setting mode.

2. Press the performance pad that corresponds with the setting you want to make.

The MASTER level indicator is lit, indicating the current value of the setting.

3. Use the rotary selector to change the value of the setting.

4. When you’ve nished making settings, press the blinking [START/STOP] button.

All of the MASTER level indicators are lit, and then all buttons and pads blink.

5. Disconnect the USB cable to power-o the DJ-202.

Pad Item Value (Bold: default) Explanation

L channel

[1] Mic audio low cut lter setting

OFF 1

2 3

4 5

6 7

8 9

Adjusts the strength of the low cut lter applied to the mic audio.

1–10 Higher values produce a stronger eect.

OFF The low cut lter is not applied.

[2] Mic audio noise gate setting

OFF 1

2 3

4 5

6 7

8 9

Species the strength of the noise gate applied to the mic audio.

1–10 As the value increases, even higher-level sound will be cut.

OFF The noise gate is not applied.

[3] Mic input eect selection

OFF Reverb

Delay Delay + Reverb

Species the eect that is applied to the mic audio.

Reverb Reverb is applied.

Delay Delay is applied.

Delay + Reverb Delay and reverb are applied simultaneously.

OFF No eect is applied.

[4] Mic input eect setting

OFF 1

2 3

4 5

6 7

8 9

Adjusts the depth of the eect that is applied to the mic audio.

1–10 Higher values apply the eect more deeply.

OFF No eect is applied.

[5] Master output adjustment

0 -3

-6 -12

-18

Adjusts the reference level of the master output.

[6] Margin at both ends of cross fader

0 1

2 3

4 5

6 7

8 9

Species the margin at both ends of the cross fader. Higher values increase the margin,

providing more play at each end of the cross fader.

[7] Demo mode time setting

OFF 1

2 3

4 5

6 7

8 9

Species the time (minutes) from when the DJ-202 was last operated until it enters demo

mode.

If this is OFF, demo mode will not operate.

[8] LED brightness adjustment

0 1

2 3

Adjusts the brightness when a button, pad, or indicator is lit.

Higher values decrease the brightness.

R channel

[1] USB mode setting

Generic Vendor

Set this as appropriate for the USB driver that you’re using.

Generic

Choose this if you want to use the generic USB driver provided by your

computer’s operating system.

* If the USB mode is set to Generic, you can not use Serato DJ Intro /

Serato DJ.

Vendor

Choose this if you want to use the dedicated DJ-202 USB driver that you

downloaded from the Roland website.

[2] Jog dial top surface sensitivity adjustment

Normal Level 1

Level 2 Level 3

Level 4 Level 5

Adjusts the sensitivity for when you take your hand o of the jog dial.

Normal Normal sensitivity.

Level 1–5 Higher values improve the response.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland DJ-202 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland DJ-202

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info