Bedienungsanleitung Roland Juno Di (Seite 90 von 136) (Englisch)

499471

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Troubleshooting

Effects not applied.

Check the following points.

• Could the effect switch be off?

Check the on/off status of each effect (p. 61).

• Are the various effect settings correct? (p. 61)

Use the included “JUNO-Di Editor” to check the following settings.

• In Performance mode, is the Output Assign setting of each part set

to “MFX”?

In some cases, such as “064: GM2 Template,” the Output Assign is

not set to “MFX” with the factory settings.

• If the send level of each effect is set to 0, the effect will not be

applied. Check the settings.

• Even with send levels to each effect set at 0, effects are not applied if

the Multi-effects Output Level, the Chorus Level, or the Reverb Level

is set to 0. Check each setting.

The Modulation or other controller is always on.

Use the included “JUNO-Di Editor” to check the following settings.

Check the Matrix Controller settings.

The JUNO-Di allows you to use the Matrix Control to control tones

(patches) in real time. The Matrix Control functions as the control

source for the Control Change and other MIDI messages received by

the JUNO-Di, and makes changes to the various tone (patch)

parameters based on these messages.

Depending on these settings, the JUNO-Di may be responding to

MIDI messages sent from external MIDI devices, and may result the

tones (patches) sounding different than intended.

Raising the chorus or reverb send level for each part of a

performance still does not cause the effect to be applied

sufficiently.

Use the included “JUNO-Di Editor” to check the following settings.

Although you can make Send level settings to the Chorus and

Reverb for each individual Part in a Performance, these values only

set the upper limit of the Chorus and Reverb Send levels for the tone

(patch) used. Accordingly, even when the value is set to the

maximum of 127, if the Send level is lowered in the tone (patch)

being used, there will be no effect. In addition, different tone (patch)

Chorus and Reverb Send level settings can be used according to

whether or not the multi-effects are used.

Using the Matrix Control or other such means to control

the LFO results in noise when the Pan is changed

suddenly.

Use the included “JUNO-Di Editor” to check the following settings.

Lower the change in speed (LFO Rate).

Due to the specialized processing used for the Pan, which alters the

volume level in each of the left and right sides, sudden Pan

movements causing rapid changes in these levels creates large

changes in volume, and noise from this may be audible as a result.

Multi-effect 43: DELAY or other delay time value is set to

the note, and then the tempo is slowed down, does the

delay time not change beyond a fixed length?

Such Delay time settings have an upper limit, so if the upper limit of

a value set to the note is exceeded when the tempo is retarded, that

upper value cannot rise any further. The upper time limit for each is

the maximum value that can be set other than the numerical value

for the beat.

The sound or performance settings (Performance) are

not saved when you perform the Write operation.

If you’re using settings that enable you to play with multiple tones

(i.e., when the [PERFORM] button is lit), the data that is saved will

depend on the location of the cursor in the Main screen (p. 58).

For example, if you want to save the Performance settings, move the

cursor to the upper line of the screen and then press the [WRITE]

button.

The Performance sounds different than when it was

written.

If you have modified the settings of a tone (patch) used by a

performance, or if the temporary patch of the performance has

been modified by an external MIDI device, these tones (patches)

must also be saved.

If tones (patches) used by a performance have been edited when

you write that performance, the JUNO-Di will display a message

asking whether you want to discard these patches. In such cases,

first save the tone (patch) or rhythm set, and then save the

performance again (p. 62).

Tones (patches) sound different than when written.

The write operation cannot be used to save tones (patches) as

changed in Patch mode using Control Change messages from an

external MIDI device.

Playlists are not shown.

This may be due to the following reasons.

• Playlists may not be shown if you directly add/delete/modify the

song data in the PLAYLIST folder without using Playlist Editor.

• For some reason the USB memory is not recognized.

• It is possible that the USB memory was not formatted correctly. The

JUNO-Di can use USB memory that has been formatted as FAT. If

your USB memory was formatted using any other method, please

re-format it using FAT.

Songs are not shown.

This may be due to the following reasons.

• Are the songs placed in the root directory?

Even if you place a song in a newly created folder, it will not be

displayed by the JUNO-Di.

Issues Related to Effects

Issues Related to Saving Data

Issues Related to Songs

JUNO-Di_e.book 90 ページ２００９年６月２２日　月曜日　午前９時２３分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland Juno Di Seite 90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info