Bedienungsanleitung Roland XV-2020 (Seite 46 von 169) (Englisch)

647722

Zoom out

Zoom in

Vorherige Seite

1/169

Nächste Seite

Creating a Patch

Patch Parameter

Tone-Related Settings

PATCH COMMON (Settings Common to the Entire Patch)

Parameter Value Description

TONE SWITCH OFF, ON Here’s how to turn on the Tones that you want to hear in a Patch. You can also use the on/off tech-

nique described in this section to audition an individual Tone by turning off all the other Tones in a

Patch.

TONE SELECT OFF, ON Selects the Tone to be edited.

Parameter Value Description

PATCH NAME space, A–Z, a–z, 0–9,

! “ # $ % & ‘ ( ) * + , - .

/ : ; < = > ? @ [ ¥ ] ^ _

` |

You can give a Patch a name of up to 12 characters. When using the XV editor,

click on the left side to name the Tone.

CATEGORY

(Patch Category)

PIANO, KEY&ORG,

GTR/BS, OCH/BRS,

SYN/PAD,

ETHNIC, RHY&SFX

Specifies the type, or “category” of the Patch. The Patch Finder uses this setting.

LEVEL

(Patch Level)

0–127 Specifies the volume of the Patch.

* You can specify the level of each Tone in a Patch using the Tone Level parameter

(TVA p. 59).

PAN

(Patch Pan)

L64–63R Sets the stereo position of the Patch. L64 pans the Patch all the way to the left, 0

is center and 63R pans it hard right.

* You can specify the pan setting for each Tone in a Patch using the Tone Pan param-

eter (TVA p. 60).

* While each Tone in a Patch has its own Pan position, the Patch pan setting shifts the

entire Patch—including all of its Tones—leftward or rightward

OUTPUT ASSIGN MFX, A, 1, 2, TONE Specifies the output destination for the Patch.

MFX: Sends the Patch into the Multi-Effects. The output destination is deter-

mined by the Multi-Effects output setting.

A: Output from OUTPUT.

1: Output from L.

2: Output from R.

TONE: Sends each Tone in the Patch to its programmed output destination.

OCTAVE SHIFT -3–+3 Sets the pitch of the Patch in units of an octave.

COARSE TUNE -48–+48 Adjusts the pitch of all of the Patch’s Tones simultaneously in semitone steps

over a range of +/-4 octaves.

FINE TUNE -50–+50 Adjusts the pitch of all of the Patch’s Tones simultaneously in 1-cent steps (1/

100th of a semitone) over a range of 1/2 semitones up or down.

STRETCH TUNE DEPTH OFF, 1, 2, 3 This setting allows you to apply “stretch tuning” to the Patch. Acoustic pianos

typically use stretch tuning, with their lower range slightly flatter and their

higher range slightly sharper than the actual mathematical tuning ratios dic-

tate. Stretch is therefore useful when programming a Patch intended to sound

like a real piano. With a setting of OFF, the Patch’s tuning is equal tempera-

ment. A setting of 3 produces the greatest difference in the pitch of the low and

high ranges. This diagram shows the pitch change relative to equal tempera-

ment that occurs in the low and high ranges. Stretch has a subtle effect on the

way in which chords resonate.

OFF

Pitch difference from

equal temperament

Parameter value

Low note range

High note range

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland XV-2020 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info