Bedienungsanleitung Roland XV-2020 (Seite 100 von 169) (Englisch)

647722

100

Zoom out

Zoom in

Vorherige Seite

1/169

Nächste Seite

100

Examples of Applications Using the XV-2020

Matrix Control

Select the controllers you want to use to control a specific Tone

parameter. Four control sources are assigned to each Patch.

SOURCE 1–4 (MATRIX CONTROL1–4 SOURCE)

Assign one of the following controllers to Control Source 1–4. If you

wish to use a controller that applies to all Patches, or a controller that

cannot be directly specified here, choose SYS-CTRL1–4, and then

choose the controller using the Control Source 1–4 parameters

(SYSTEM CONTROL SOURCE).

MATRIX CONTROL1–4

This select the parameters to be controlled in the Matrix Control 1-4

Source and the Sens settings, as well as the Tone to which they’re

applied. Up to four parameters can be specified for each controller

and controlled simultaneously.

DESTINATION1–4

(MATRIX CONTROL1–4 DESTINATION1–4)

This chooses the parameters to be controlled.

SENS1–4 (MATRIX CONTROL SENS 1–4)

This adjusts the amount of change that occurs in response to

controller movements. Negative (-) values invert the change. For

example, with LFO Depth, the phase is reversed when a negative

Sens value is chosen. With LFO Rate, setting Sens to a negative value

increases the cycle length, slowing down the LFO, while setting it to

positive value shortens the cycle, speeding it up

TONE1–4 (MATRIX CONTROL1–4, TONE CONTROL

SWITCH1–4)

This selects the Tone to be controlled using the two previous

parameter settings. “ON” activates the control of a Tone, “OFF” de-

activates it, and “REV” reverses the (+) or (-) nature of the change

being applied.

Applications for Patches

Syncing the LFO Cycle to the

System Tempo

1. Click [PATCH].

2. Click the for [PATCH NAME] to select the Patch to be

synchronized.

fig.08-01.eps_50

fig.08-02.eps_50

3. Click [DETAIL] for PATCH COMMON, then set [CLOCK

SOURCE] to [SYSTEM].

fig.08-06a.eps_50

fig.08-06b

4. Click [DETAIL] for LFO 1, click [RATE], then set each tone’s

Rate to the note length corresponding to the

synchronization tempo.

fig.08-07

* TONE 1 – TONE 4 are switched with TONE SELECT, at the upper

right of the screen.

OFF (No controller is used.)

CC01–95 (Controller numbers 1–95 (except for 32))

PITCH BEND

AFTERTOUCH

SYS-CTRL1–4 (System Control 1–4)

VELOCITY

KEYFOLLOW

TEMPO

LFO1(2)

PITCH ENV (Pitch Envelope)

TVF ENV (TVF Envelope)

TVA ENV (TVA Envelope)

OFF (No control) ---

PITCH p. 54

CUTOFF (Cutoff Frequency) p. 57

RESONANCE p. 57

LEVEL p. 100

PAN p. 100

DRY LEVEL p. 78

CHORUS SEND (Chorus Send Level) p. 78

REVERB SEND (Reverb Send Level) p. 78

LFO1(2) PITCH DEPTH p. 57

LFO1(2) TVF DEPTH p. 57

LFO1(2) TVA DEPTH p. 57

LFO1(2) PAN DEPTH p. 57

LFO1(2) RATE p. 56

PCH ENV A-TIME (Pitch Envelope Attack Time)

p. 54

PCH ENV D-TIME (Pitch Envelope Decay Time)

PCH ENV R-TIME (Pitch Envelope Release Time)

TVF ENV A-TIME (TVF Envelope Attack Time)

p. 58

TVF ENV D-TIME (TVF Envelope Decay Time)

TVF ENV R-TIME (TVF Envelope Release Time)

TVA ENV A-TIME (TVA Envelope Attack Time)

p. 60

TVA ENV D-TIME (TVA Envelope Decay Time)

TVA ENV R-TIME (TVA Envelope Release Time)

TMT p. 49

FXM DEPTH (Wave FXM Depth) p. 54

MFX CTRL 1–4 (MFX CONTROL 1–4) p. 80

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland XV-2020 Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info