Bedienungsanleitung Ronco Pocket Fisherman (Seite 3 von 4) (Englisch)

638843

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Notes for Opening the Side Door for

Cleaning or for Changing the Fishing Line

First turn crank handle one full revolution clockwise. Do not depress

the thumb brake during reel removal. Push on the release button to

open the side door. Grasp the crank handle and pull the reel out. Take

off the hex nut, two washers and the metal spincast cover.

With the reel removed, you may replace your line spool with another

spool (either pre-loaded or one you load yourself) containing the

desired test line. Additional spools are available from Ronco.com.

When you start your new line, use a half hitch to keep the line in place

without slipping.

NOTE: When replacing the spool, do not force it. If reel assembly

does not ﬁt back into housing, check to see that the thumb brake is

not depressed.

You don’t need to remove the handle or the star drag to change the

line or clean the reel case.

If you ﬁnd an extra piece that looks like an arc (17), it

belongs on the shaft below gear B (8) with the tab facing

into the spincast bracket (10).

It resides behind the back

of the bracket (10) that holds the spool.

How to Install Line on the Reel

• Remove the snap-ﬁt side door by depressing the snap and pulling

the door away from the reel body.

• Thread the line through the ﬁrst rod line guide, the second guide and

then through the back of the rod.

• Remove the hex nut, washers and metal spincast cover. You will

need a small nail or screwdriver to gently push the spring pin back

through the window in the spincast cover. Set the spincast cover

aside. Remove any old line from spool. Tie new line onto the spool.

• Replace spincast cover again push (or pull gently with small pliers)

the small pin outward so the metal spincast cover it will go on correct-

ly. Replace the washers and hex nut.

• Prior to winding new line on, rotate the handle of the reel and deter-

mine which way the spinnerhead is rotating. Lay the spool of line on

its side so the line comes off in the same direction the spinnerhead is

turning.

• Replace side door while being careful not to pinch the line.

• Start winding

the line under tension from your ﬁnger. The correct

amount of line should ﬁll the spool to within 1/8 inch from the top of the

reel spool lip. Gently ﬁll it to full and then pull about 10 yards back out

and cut it off. The plastic spool should be about 1/8” from “full”.

Metal Spincast Cover

To remove or put back on this

cover, use a very small nail or

screwdriver in its view hole to

gently hold the spring pin back.

A Line Spool

Load it no more than

1/8” from outside

edge.

7 to 10 lb test line is

ﬁne for this rod &

reel.

Keep tension on the

line when reeling in

and when loading

new line.

How to Change the Spool

Remove the side door by depressing the snap and pulling the door

away from the reel housing. remove the hex nut while ﬁrmly holding

the spinnerhead. Lift off the spincast cover by pulling out on its side

pin with small pliers. If you want to remove the spool, turn it (view from

back to see the two pegs come free). Install new spool. Replace spin-

cast cover, washers and hex nut. Bring line through the line guide in

front and on to the rod tips. Replace side door. Add a good swivel to

end of the line. Set drag to desired setting.

1 Cap Nut

2 Reel Handle

3 Star Drag

4 Side Release Button

5 Side Door

6 Gear A Shaft

7 Gear A

8 Gear B

9 Gear B Shaft

10 Spincast Bracket - Black

11 Spool - Plastic

12 Spincast Cover - Metal

13 Hex Nut

14 Line Exit Hole

15 Line Guides

16 Fishing Rod

17 Brake Arc

18 Spacer Washer - Brass

Rubber Snubbers for Bigger Fish

For larger ﬁsh a long rod has one advantage over a short one – it

bends to cushion the strike. That’s why we recommend using a rub-

ber shock absorber and up to 20 lb. test line when you’re after these

"big ﬁsh" with the Pocket Fisherman

™

. Attach the shock absorber to

the line before the hook or lure. It helps set the hook and keep it there

by elastic pressure.

These shock absorbers or "rubber snubbers" are available at many

tackle shops.

13 Hex Nut

12 Spincast Cover - Metal

11 Spool of Line - Plastic

1 Cap Net

2 Reel Handle

3 Star Drag

5 Side Door

10 Spincast Bracket - Black

18 Spacer Washer - Brass

8 Gear B

9 Gear B Shaft

7 Gear A

17 Brake Arc

6 Gear A Shaft

4 Side Release Button

14 Line Exit Hole

15 Line Guides

16 Folding Rod

Caution:

Remember to

always use care

when ﬁshing.

Use extra care

with sharp

hooks, lures,

plugs and when

taking ﬁsh off

the line.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ronco Pocket Fisherman Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info