Bedienungsanleitung Rossmax SA120 (Seite 2 von 2) (Englisch)

783667

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Introduction Battery installation

Probe connection

How to measure

Preview Default Setting

How to Change Default Setting

Rossmax Handheld Pulse Oximeter is used to measure oxygen saturation in blood

(SpO2) and pulse rate, also to issue warnings immediately. It is a non-invasive

device intended for spot-check of adults, child, and infants with corresponding

probe applied at home, hospital and clinics. The probe contains a dual light

source and a photodetector.

Attention: Consult the accompanying documents. Please read this manual

carefully before use. Please be sure to keep this manual.

1. Use thumb to slide battery cover out.

2. Insert or replace 4 “AA” batteries according to the (+/-) polarity.

Caution: Need to replace when the batteries icon “ ” is blinking on display/

while pressed the function button and nothing appears on display.

Caution: Batteries may leak or explode if used or disposed of improperly. Remove

batteries if the device will be stored for long time. Do not use different

types or brand of batteries at the same time.

Rossmax PA100/ PC100 or compatible probe is used. (Please install carefully.)

Caution: It may damage the efficiency of the device if not apply with a Rossmax

compatible probe.

1. Press the Power On button for 1 second, when the device activates, the beep

sound will last for 2 second.

Note: After the device activates, the software version will pop up directly. For first

time activates, it will directly jump to time setting. (Please refer to setting

instruction.)

2. Information of software version appears; insert one finger to probe, nail side up,

for self-test.

Notes: The device will turn itself off automatically after 1 minute idling with two

beep sounded.

3. The pulse strength shows “ “, pulse oximeter begins its measurement.

Notes: The heartbeat is sounded though the buzzer. If need to become silence

mode, press the sound button and the LCD screen will have the sound

icon shown. If need the heartbeat sound, press the sound button to exit.

4. Your SpO2 and pulse rate values will appears on the screen after few seconds.

Notes: 1. Don’t remove your finger until the measurement is completed.

2. Any other problems or unrecognized icon, please refer to trouble shooting.

1. Press the button 1 second to preview default setting value.

2. Press to exit preview default mode or wait for 3 second for automatically.

Press the button 2 second to

enter the set up mode and change

default. For jump to next setting,

press after finishing. To exit, press

or wait for 10 second.

SPO2 mode

• To setup Max SpO2 rate, press

to enter, and it shows as

picture and press / button

for adjustment. To set up Min SpO2

rate, press , and it shows

as picture and same as max setting.

Pulse Rate mode

• To setup Max Pulse rate, press

to enter, and it shows as

picture and press / button

for adjustment. To set up Min Pulse

rate, press , and it shows

as picture and same as max setting.

Memory interval mode

1. Optional of SA120: 5 / 10 / 30 / 60

minutes.

2. While the memory mode, the

memory interval mode

appears on the screen. To

change the default, press /

to change (5)-(10)-(30)-(60) or

(60)-(30)-(10)-(5) minutes.

Sound volume control

• For the control of sound volume,

for loud volume, for lower

volume. To change the sounds

volume, Press / to change

--> .

Time Setup

• To set up the time, it starts from

year as picture, and press /

to adjust. Following the same

frequency for month, date, hour

to minutes.

Warning: Press or wait for 10 seconds to exit, the setup value will be reserved.

Please double-check the set value before use.

Name/ Functions of each part

Pulse Oximeter

No. Item Purpose

1Pulse strength

2Probe icon

3LCD backlight button For light on/ o

4Sound button

For Heartbeat sound

loud volume

lower volume

silence

5 Time Shows the time

6SpO2 icon High SpO2

Low SpO2

7Pulse Rate High Pulse Rate

Low Pulse Rate

8UP/DOWN button For adjust/view all setting/ memory

memory icon

9Set button For view/ adjust default setting

10 Alert button Alert o / Alert pause

11 Power button Power on/ o

12 Battery compartment

For install or replace batteries

Full batteries

out of batteries

SA120 All symbols

second

2 seconds

High SpO2

Low SpO2

100

SA120 All symbols

High

Pulse Rate

Low

Pulse Rate

140

135

130

125

…

SA120 All symbols

Memories reading and delete

Enter the memory mode with the or to read the SpO2 and pulse rate in

memory mode.

Note: When entering the memory reading mode, the will appear on the

screen.

SA120 All symbols

seconds

2 seconds to

clean data

Press for two second during the memory reading mode, it will enter the

memory delete mode. The screen show and means not to delete any

data, while the screen with and , it means to delete data.

Caution: The deleted data could not be restored.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rossmax SA120 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info