Bedienungsanleitung Rotel RDD-1580 (Seite 9 von 12) (Englisch)

577720

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Connections

NOTE: To prevent loud noises that neither you nor your speakers will

appreciate, make sure the system is turned off when you make any

signal connections.

Front USB Input

See figure 5

The front USB input can be connected to an iPod, iPhone, USB flash memory

or the Bluetooth dongle (supplied) for wireless streaming. With iPod or

iPhones, simply plug the device into the front USB and select USB function

from the source selector. The iPod and iPhone remain active allowing search

and play functions.

Bluetooth Connection

See figure 5

Insert the supplied Bluetooth Dongle into the front USB for wireless streaming

via Bluetooth, from your device (i.e. mobile phones) to the RDD-1580. From

your mobile device, look for „Rotel Bluetooth‰ and connect to it. Connection

is normally automatic, but if prompted for a password, please press „0000‰

on your device.

NOTE: Not all Bluetooth dongles will operate with RDD-1580. Please

use the one supplied.

Analog Outputs

See figure 3 and figure 4

A pair of standard RCA jacks and XLR balanced connectors supplies an

analog output signal from the RDD-1580 to the source inputs of an audio

preamplifier, integrated amplifier, or receiver.

NOTE: You should choose only one method of analog connection from

the RDD-1580. Do not connect both the RCA and XLR at the same time.

Select high quality audio interconnect cables. Connect the left and right

channel outputs of the RDD-1580 to the corresponding inputs on the

preamplifier or other component.

Digital Inputs

See figure 3

There are two sets of digital inputs labeled COAX 1 and 2, OPT 1 and 2.

Connect the COAXIAL or OPTICAL PCM outputs of your source component

into these sockets. The digital signals will be decoded and played by the RDD-

1580. The unit is capable of decoding PCM signals up to 24 bit, 192kHZ.

PC-USB Input

See figure 3

Connect this input using the supplied USB cable to the USB socket of your

computer.

The RDD-1580 supports both USB Audio Class1.0 and USB Audio Class 2.0

modes. Windows computers do not require installation of a driver for USB

Audio Class 1.0 and supports playback of audio up to 96KHz sampling

rates. The Factory Default setting is USB Audio Class 1.0.

To take advantage of USB Audio Class 2.0 audio playback supporting

up to 192KHz sampling rates you will need to install the Windows driver

supplied on CD included with the RDD-1580. You will also need to switch

the RDD-1580 to USB Audio Class 2.0 playback mode with the following:

1. Press and Hold the PC-USB source button on the front panel for 5 seconds.

The current USB audio mode is indicated by the blinking Sample Rate LED as:

USB Audio Class 1.0 ă Sample Rate 96KHz blinking [Factory Default]

USB Audio Class 2.0 ă Sample Rate 192KHz blinking

2. Press the PC-USB key again to illuminate the 192K sample rate light blinks.

3. Pressing the PC-USB key will toggle between USB Audio Class 1.0 (96KHz

light blinks) and USB Audio Class 2.0 (192KHz light blinks).

4. After the desired USB Audio mode is selected wait 3 seconds for the

selection period to end and the RDD-1580 will use the selected audio mode.

5. Power cycle the RDD-1580 and your PC after changing the USB Audio

mode to ensure both units are properly configured.

Many audio playback applications do not support 192KHz sampling rate.

Please confirm your audio player supports 192KHz audio and you have

192KHz audio files to properly playback this sample rate. Also, you may

need to configure the audio driver in your PC to output 192KHz or your

computer may „down sample‰ to a lower audio sample rate. For more

information please refer to your audio player or operating system information.

NOTE: USB Audio Class 2.0 required installation of the Windows PC

driver on the CD ROM included with the RDD-1580. MAC computers do

not require a driver to support PC-USB 1.0 or 2.0 audio.

NOTE: Upon successful installation of the driver, you may need to select

the ROTEL audio driver from the audio/speaker setup of your computer.

Computer I/O Connector

The RDD-1580 can be controlled via RS232 for integration with automation

systems. The COMPUTER I/O input accepts a standard straight DB-9 Male-

to-Female cable.

For additional information on the connections, software, and operating codes

for computer control of the RDD-1580, contact your authorized Rotel dealer.

ROTEL LINK

This 3.5 mm stereo mini-jack (labeled ROTEL LINK IN) can optionally attach

to Rotel network enabled products with ROTEL LINK OUT connections. This

allows the attached Rotel products to communicate with each other and

be controlled via the Rotel Remote App (available for download on the

iTunes

store).

EXT REM IN Jack

This 3.5mm mini-jack receives command codes from industry-standard infrared

receivers via hard-wired connections. This feature could prove useful when

the unit is installed in a cabinet and the front-panel sensor is blocked. Consult

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel RDD-1580 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info