Bedienungsanleitung Rotel rdv 1060 (Seite 27 von 32) (Englisch)

137947

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English

Audio Setup

-- AUDIO SETUP --

DYNAMIC RANGE COMPRESSION

SETUP MENU -- MAIN PAGE

GO TO AUDIO SETUP

DIGITAL OUT

FULL

LPCM OUTPUT

6/8

MAIN PAGE

4/8

2/8

COMPRESS

-- AUDIO SETUP --

SET DIGITAL OUT

DIGITAL OUT OFF

STREAM/PCM

LPCM OUTPUT

MAIN PAGE

COMPRESS

-- AUDIO SETUP --

SET LPCM OUTPUT TO 48K OR 96K

DIGITAL OUT

LPCM OUTPUT LPCM 48K

LPCM 96K

MAIN PAGE

COMPRESS

-- AUDIO SETUP --

BACK TO MAIN PAGE

DIGITAL OUT

LPCM OUTPUT

MAIN PAGE

COMPRESS

EXIT SETUP

AUDIO SETUP

PREFERENCES

SPEAKER SETUP

GENERAL SETUP

OFF

The AUDIO SETUP page provides three ad-

justment items that configure playback of digital

recordings. The first item activates or disables

the digital output. The second item sets the pa-

rameters for Dolby Digital dynamic range

compression. The third item sets a maximum

sampling rate for the digital output.

To reach the AUDIO SETUP PAGE, use

the CURSOR

buttons to highlight the

AUDIO SETUP line on the MAIN PAGE. Then,

press the PLAY/ENTER

button.

To return to the MAIN PAGE, use the CUR-

SOR

buttons to scroll down and highlight

the MAIN PAGE line. Then, press the PLAY/

ENTER

button.

The following instructions describe each ad-

justment item on the AUDIO SETUP PAGE and

the available settings. The default settings for

each item are shown in the illustration.

COMPRESS

When playing a Dolby Digital DVD-Video disc,

the RDV-1060 can compress the dynamic range

of the audio signal. This reduces the difference

between quiet sounds and loud sounds and

may be desirable if your system is taxed by

loud passages or for listening at low volumes.

The compression is quite sophisticated, using

instructions embedded in the digital data stream

To adjust, use the CURSOR

buttons to select

a setting on the vertical slider control on the

right side of the menu screen. The “OFF” set-

ting provides no compression and the full

dynamic range of a Dolby Digital recording.

The “FULL” setting provides maximum avail-

able compression and reduces the dynamic

range of a Dolby Digital recording to that of

a typical VHS Hi-Fi recording. Settings in

between these two extremes provide progres-

sively more compression.

NOTE

: This menu item only has an effect for

Dolby Digital recordings and is ignored for

other types of recordings

LPCM OUTPUT

The RDV-1060’s digital output can send an LPCM

(linear pulse code modulation) bitstream to the

receiver or surround processor. These LPCM

bitstreams can have different sampling rates,

depending on the format of the recording. For

example, Audio CDs generate a 44.1 kHz bit-

stream. A 2-channel LPCM soundtrack from a

DVD-Video disc generates a 48 kHz bitstream.

Some DTS DVD-Video discs generate a 96 kHz

bitstream. Since the bitstream must be decoded

by the receiver, it is important not to send a

signal that the receiver cannot process.

LPCM 48K: Choose this setting if your re-

ceiver cannot handle a digital bitstream with

a sampling rate higher than 48 kHz.

LPCM 96K: Choose this setting if your re-

ceiver can handle a digital bitstream with a

sampling rate up to 96 kHz. Even with this

default setting, a disc recorded with a 44.1

kHz or 48 kHz sampling rate will still be sent

to the receiver at the lower rate. This setting

simply specifies a maximum sampling rate.

NOTE

: The RDV-1060 can process sampling

rates up to 192 kHz. However, this amount

of data cannot be sent to receivers or proces-

sors with the currently available digital con-

nections. These recordings must be decoded

and sent to the receiver as analog signals.

DIGITAL OUT

Use this setting to turn on or disable the digi-

tal bitstream sent from the RDV-1060’s coax

or optical digital outputs to a digital input on

the surround sound receiver or processor. In

most systems, this digital connection is the

preferred method of sending Dolby Digital or

DTS signals to the receiver, allowing the

receiver’s digital processors to decode the

multichannel signal.

STREAM/PCM: Use this setting to activate

the digital output.

OFF: Use this setting to disable the digital

output.

NOTE

: The digital bitstream is automatically

disabled when playing the PCM soundtrack

from a DVD-Audio disc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel rdv 1060 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info