Bedienungsanleitung Rotel RMB-1575 (Seite 8 von 26) (Deutsch, Englisch, Holländisch)

489964

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

RMB-1565 / RMB-1575 Five Channel Power Ampliﬁ ers

+12V Trigger Input and Output

The jack labeled IN is for connecting the 3.5mm Plug/Cable carrying

a +12 volt trigger signal to turn the ampliﬁ er on and off. To use this

feature the adjacent switch must be placed to the 12V TRIG position

(see previous section). This input accepts any control signal (AC or DC)

ranging from 3 volts to 30 volts.

The jack labeled OUT is for connecting another 3.5mm plug/cable

to provide a 12V trigger signal to other components. The 12V output

signal is available whenever a +12 volt trigger signal is applied to the

IN connector.

Protection Indicator

Thermal and protection circuits protect the ampliﬁ er against potential

damage in the event of extreme or faulty operating conditions. Unlike

many designs, the protection circuit in the RMB-1565 and RMB-1575

is independent of the audio signal and has no impact on sonic

performance. Instead, the protection circuit monitors the temperature

of the output devices and shuts down the ampliﬁ er if safe limits are

exceeded.

In addition, the ampliﬁ er includes over-current protection which

operates only when load impedances drop too low. This protection is

independent for each of the ﬁ ve channels .

Should a faulty condition arise, the ampliﬁ er channel at fault will stop

playing and the PROTECTION LED on the front panel will light.

If this happens, turn the ampliﬁ er off, let it cool down for several

minutes, and attempt to identify and correct the problem. When you

turn the ampliﬁ er back on, the protection circuit will automatically reset

and the PROTECTION LED should go out.

In most cases, the protection circuitry activates because of a fault

condition such as shorted speaker wires, or inadequate ventilation

leading to an overheating condition. In very rare cases, highly reactive

or extremely low impedance speaker loads could cause the protection

circuit to engage.

Input Signal Connections

See Figure 2

The RMB-1565 and RMB-1575 have standard unbalanced RCA-type

input connectors, the type used on nearly all audio equipment. There is

an RCA input for each of the ﬁ ve ampliﬁ er channels. These RCA inputs

accept audio signals from preampliﬁ ers or surround sound processors.

Use high quality audio interconnect cables for best performance.

Speakers

The RMB-1565 and RMB-1575 have ﬁ ve sets of speaker connectors,

one for each ampliﬁ er channel.

Speaker Selection

The nominal impedance of the loudspeaker(s) connected to each

channel of the ampliﬁ er in the various operating modes should be no

lower than 4 ohms.

Speaker Wire Selection

Use insulated two-conductor stranded wire to connect the ampliﬁ er to

the speakers. The size and quality of the wire can have an audible

effect on the performance of the system. Standard speaker wire will

work, but can result in lower output or diminished bass response,

particularly over longer distances. In general, heavier wire will

improve the sound. For best performance, you may want to consider

special high-quality speaker cables. Your authorized Rotel dealer can

help in the selection of appropriate cables for your system.

Polarity and Phasing

The polarity – the positive/negative orientation of the connections

– for every speaker and ampliﬁ er connection must be consistent so

all the speakers will be in phase. If the polarity of one connection is

mistakenly reversed, bass output will be very weak and stereo imaging

degraded. All wire is marked so you can identify the two conductors.

There may be ribs or a stripe on the insulation of one conductor. The

wire may have clear insulation with different color conductors (copper

and silver). There may be polarity indications printed on the insulation.

Identify the positive and negative conductors and be consistent with

every speaker and ampliﬁ er connection.

Speaker Connections

See Figure 2

Note: The following text describes both binding post and

plug-in connections. DO NOT use both connection methods in

combination to connect multiple speakers.

The RMB-1565 and RMB-1575 have two color coded terminals for

each ampliﬁ er channel. These speaker connectors accept bare wire,

connector lugs, or “banana” type connectors (except in the European

Community countries where their use is not permitted).

Route the wires from the ampliﬁ er to the speakers. Give yourself

enough slack so you can move the components to allow access to the

speaker connectors.

If you are using banana plugs, connect them to the wires and then

plug into the backs of the speaker connectors. The collars of the

speaker connectors should be screwed in all the way (clockwise).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel RMB-1575 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info