Bedienungsanleitung Rotel RSX-1056 (Seite 42 von 46) (Englisch)

498117

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

RSX-1056 Surround Sound Receiver

Contour Setup

CONTOUR SETUP

SPEAKER:Front

DEFEAT:On

HF CONTOUR:+5

LF CONTOUR: 0

MAIN MENU

The CONTOUR SETUP menu allows digital

adjustment of the bass and treble response of

each group of speakers in the system. For

example, if your center channel speaker sounds

too bright, you could roll off the extreme high

frequencies.

SPEAKER (front/center/surround/cen-

ter back/all): Select which speaker or group

of speakers to adjust. Selecting ALL permits

adjustment of the entire system as a whole.

DEFEAT (on/off): Selecting the ON setting

defeats the contour adjustment, bypassing the

contour processing entirely for that speaker

or group of speakers.

HF CONTOUR: Adjusts the extreme high fre-

quency slope over a range of -6dB (MIN) to

+6dB (MAX). Negative number settings reduce

the high frequency output; positive number

settings increase it.

LF CONTOUR: Adjusts the extreme low fre-

quency slope over a range of -6dB (MIN) to

+6dB (MAX). Negative number settings reduce

the low frequency output; positive number

settings increase it.

The contour adjustments are designed to work

at the frequency extremes and be relatively

subtle so that they do not have a negative impact

on midrange sounds. We recommend accli-

mating to the sound of the system with the

contour adjustments defeated and then mak-

ing adjustments, if necessary, to address spe-

cific speaker response issues or personal taste.

NOTE

: You can also make temporary contour

adjustments using the TONE and UP/DOWN

buttons on the remote. See the Contour/Tone

Settings section of this manual for details.

Miscellaneous Settings

Other Options

OTHER OPTIONS

RECORD:Source

TURN ON VOL:Last

MAX VOL:Max

VOL SPEED:Slow

POWER:Standby

LANGUAGE:English

VIDEO:NTSC

OSD:On

PROGRESSIVE:NO

MAIN MENU

This OTHER OPTIONS menu, accessed from

the MAIN menu, provides access to several

miscellaneous settings as follows:

RECORD: Select which source signal to be

sent to the recording outputs by choosing one

of the input sources. The options are: CD, TAPE,

TUNER, VIDEO 1–5, and SOURCE. You can

either select a specific component or select

SOURCE which will send the signal to the

record outputs from whatever source is selected

for listening.

TURN ON VOL: Specifies a default volume

level to be used each time the RSX-1056 is

activated. You can select LAST to have the

RSX-1056 power up with the last previously

used volume setting. Or, you specify a volume

from MIN (full mute) to MAX, in 1dB incre-

ments. Note that this setting cannot exceed

the MAX VOL established in the next line of

the menu.

MAX VOL: Specifies the maximum volume

level for the RSX-1056. The volume cannot be

adjusted above this level. Settings range from

MIN to MAX, in 1dB increments.

VOL SPEED: Provides three options for how

rapidly the volume control responds to inputs.

The SLOW setting adjusts the volume 1dB with

each control input. The MID setting adjusts in

2dB increments. The FAST setting adjusts in

3dB increments.

POWER: This setting determines how the

RSX-1056 powers up.

With the default STANDBY setting, the unit

powers up in standby mode when AC is ap-

plied and the rear panel POWER button is ON.

The unit must be activated using the front panel

STANDBY button or the remote ON/OFF

buttons.

With the DIRECT setting, the unit is fully acti-

vated when AC power is applied and the rear

panel POWER button is ON; however, it may

be put in standby mode using the front panel

STANDBY button or the remote ON/OFF

buttons.

In ALWAYS-ON mode, the unit remains fully

active whenever AC is present and the rear

panel POWER button is ON; the front panel

STANDBY button and the remote ON/OFF

buttons are disabled and the unit cannot be

put in standby mode.

LANGUAGE: Selects a language for the On

Screen Display.

VIDEO: Specifies whether an NTSC or PAL

television monitor is connected to the TV

MONITOR outputs of the RSX-1056. This set-

ting must be correct for the upconversion and

OSD menus to work properly.

OSD ON/OFF: Select whether or not status

information (such as the volume setting) is

displayed on the TV monitor.

PROGRESSIVE: The OSD menus cannot be

displayed on the TV monitor when progres-

sive scan or 1080i HDTV video signals are

being used at the Component Video inputs.

This setting enables a feature that allows the

display of the main OSD setup menus (but not

the information displays such as volume, etc.)

on the TV monitor by interrupting the progressive

scan video signal and restoring it after the OSD

menus are cancelled. Choose the video input

or combination of video inputs for progres-

sive scan or HDTV video signals (480p, 720p,

1080i). All other video inputs will be assigned

as standard interlaced video inputs. Video 4

and 5 cannot be assigned as progressive scan

inputs.

NOTE

: When a video input or inputs are se-

lected for progressive mode, the conversion

from composite or S-Video to Component

Video output is not available for those inputs.

The conversion from composite or S-VIDEO

to Component Video output is only available

for the other video inputs. For example, if

Video 1 and Video 2 are selected for pro-

gressive scan signals (V1+V2), conversion

from composite or S-Video is only available

for Video 3, 4, and 5.

Rotel RSX-1056 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info