Bedienungsanleitung Rotel RSX-1560 (Seite 43 von 54) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

489979

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

42 43

English

RSX-1560 Surround Sound Receiver

42 43

English

RSX-1560 Surround Sound Receiver

Multi Input Setup



















When the MULTI INPUT source is selected on the INPUT SETUP menu, the

available options change to reﬂect the fact that these inputs are direct

analog inputs and bypass the receiver’s digital processing. The INPUT,

CINEMA EQ, DEFAULT MODE and GROUP DELAY options are not

available since these are all digitally implemented features.

The VID INPUT, INPUT LABEL, INPUT ATT and 12V TRIGGER options are

still available and work as described on the previous menu.

One additional option, LFE REDIRECT, provides an alternative bass

management conﬁguration. Typically, the eight channels of the MULTI

INPUT are conﬁgured as pure analog bypass signals, going straight

from the inputs to the volume control and the preamp outputs, bypassing

all of the digital processing. There are no crossovers and no bass

management; therefore, whatever signal goes into the subwoofer

channel will be sent to the subwoofer preamp output.

This conﬁguration may not be ideal for multichannel systems conﬁgured

with high-pass speakers, redirecting bass to a powered subwoofer. An

option, called LFE REDIRECT, sends the seven main channels directly

to the outputs as usual. In addition, it takes a duplicate copy of these

seven channels, combines them into mono, and routes them through a

100Hz analog low-pass crossover to the subwoofer preamp output. This

creates a summed mono subwoofer signal, derived from the seven main

channels of the MULTI INPUT.

Use the LFE REDIRECT OFF setting for the pure analog bypass

conﬁguration. Use the LFE REDIRECT ON setting to derive the mono

summed subwoofer output.

Dolby Pro Logic IIx

��





















When Dolby Pro Logic IIx is selected as the default surround mode on

the INPUT SETUP menu, there are additional settings and parameters to

optimize the surround decoding for music or movie soundtracks. Dolby

Pro Logic II uses matrix decoding algorithms to derive a center channel

and surround channels from 2-channel source material.

The ﬁrst line of the Dolby Pro Logic IIx sub-menu selects CINEMA,

MUSIC, GAME, or PRO LOGIC modes for matrix decoding. Use the

+/– buttons on the remote to select a mode.

Select CINEMA to optimize for Dolby Surround encoded movie

soundtracks including increased surround separation and full-bandwidth

surround channel frequency response.

Select MUSIC to optimize for musical recordings. When the MUSIC

mode is selected, three additional parameters will be available on the

OSD screen. Use the UP/DOWN buttons on the remote to select a

parameter. Use the +/– buttons to change the selected parameter as

follows:

• PANORAMA: The Panorama option extends the front stereo image

to include the surround speakers for a dramatic “wraparound” effect.

The options are OFF or ON.

• DIMENSION: The Dimension option allows you to gradually adjust

the soundﬁeld towards the front or towards the rear. There are seven

incremental settings from 0 to 6. A setting of 0 shifts the soundﬁeld

towards the rear for maximum surround effect. A setting of 6 shifts

the soundﬁeld to the front for minimum surround effect. The default

setting of 3 provides a “neutral” balance between the two extremes.

• CENTER WIDTH: The Center Width option allows you to spread

the signal intended for the center speaker to the left and right

front speakers, widening the perceived soundﬁeld. There are eight

incremental settings from 0 to 7. With the default setting of 3, there is

no center width spreading and all of the center channel information

is sent to the center speaker. The maximum setting of 7 shifts all of the

center channel signal to the left and right speakers, essentially muting

the center speaker and maximizing the soundﬁeld width. Other

settings provide incremental steps between the two extremes.

Select GAME to optimize for Dolby Surround encoded video games.

Select PRO LOGIC for original Dolby Pro Logic decoding. Typically,

Pro Logic II (Cinema or Music modes) will provide better surround

performance, even with older source material. Original Pro Logic mode

provides 5.1 channel surround sound, even on 6.1/7.1 channel systems.

When you have completed all the desired adjustments, highlight the

INPUT SETUP MENU line at the bottom of the screen and press the

ENTER button to return to the INPUT SETUP menu (or just press the

ENTER button).

DTS Neo:6

��

��

















When DTS Neo:6 is selected as the default surround mode on the

INPUT SETUP menu, there are additional option settings and parameters

available to optimize the surround decoding for various types of

recordings, music or movie soundtracks. DTS Neo:6 uses matrix

decoding algorithms to derive a center channel and surround channels

from 2-channel source material.

RSX-1560 English v2.indd 43 29/9/08 15:16:13

Rotel RSX-1560 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info