Bedienungsanleitung Rotel rt 02 (Seite 6 von 11) (Englisch)

161420

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Rear Panel Connections

The RT-02 provides rear panel connections for

audio line level output, an FM antenna, an AM

antenna, a 12V Trigger, a remote IR sensor,

and AC power input.

NOTE: Do not plug any system component into

an AC source until system hookup is complete

and you are confident that all component-to-

component connections have been properly

made.

RCA Outputs

Line level RCA audio outputs send a fixed-level

stereo signal from the RT-02 to your pream-

plifier, system controller, or integrated amplifier.

Use a standard RCA audio cable to connect

the LEFT OUTPUT jack to the left channel tuner

input on your system controller and the RIGHT

OUTPUT jack to the right channel tuner input

on your system controller.

AM Loop Antenna

The RT-02 includes a loop antenna to receive

AM radio signals. Remove this antenna from

the box and locate it near the RT-02.

Connect the 300 ohm twin-conductor wire from

the loop antenna to the pair of screw termi-

nals labeled AM LOOP, attaching one wire

to each terminal. It does not matter which wire

attaches to which terminal, but make sure that

the connections are solid and that the two wires

do not touch.

You may need to rotate or otherwise reorient

the antenna to find the best position.

NOTE: To use an outdoor antenna, connect

its 300 ohm twin-conductor wire to the G and

AM terminals in place of the loop antenna,

only after a professional contractor has in-

stalled the antenna system in accordance with

local electrical codes.

FM Antenna

The RT-02 is supplied with a T-shaped indoor

FM antenna. Remove this antenna from the

box and connect its attached coax F-type plug

to the FM antenna connector on the RT-02. For

best reception, unfold the T-shaped antenna.

Eyelets at both ends of the T allow tacking the

antenna to a wall, if desired. Experiment with

positioning for best reception.

NOTE: To use an outdoor antenna, connect

its 75 ohm coax lead wire to the FM connec-

tor in place of the indoor wire antenna, only

after a professional contractor has installed

the antenna system in accordance with local

electrical codes. In the USA, you will need to

use the supplied F-type converter to connect

the 75 ohm coax cable to the antenna input.

AC Input

Your RT-02 is configured at the factory for the

proper AC line voltage in the country where

you purchased it (115 volts AC at 60Hz in

the USA and 230 volts AC at 50Hz in Europe).

The AC line configuration is noted on a de-

cal on the back of your unit. Make sure that

your unit is configured properly for your AC

line voltage.

Plug the supplied cord into the AC INPUT

receptacle on the back of the unit. Once all

other rear panel connections are completed,

plug the power cord into an AC wall outlet

or switched AC outlet on another system com-

ponent.

12V TRIGGER Connection

The RT-02 can be activated by a 12 volt trig-

ger signal from a Rotel preamplifier.

The trigger input accepts any control signal

(AC or DC) ranging from 3 volts to 30 volts.

When a cable is connected to the input and

a trigger signal is present, the tuner is acti-

vated. When the trigger signal is interrupted,

the tuner goes into standby mode. The front

panel indicator light remains lit, but the dis-

play goes dark and the unit will not operate.

NOTE: When using the 12V Trigger feature,

leave the POWER button in the ON position.

EXT REMOTE IN Jack

This 3.5mm mini-jack receives command codes

from industry-standard infrared receivers

(Xantech, etc.) via hard-wired connections. This

feature could prove useful when the unit is

installed in a cabinet and the front-panel sensor

is blocked. Consult your authorized Rotel dealer

for information on these external repeaters and

the proper wiring of a jack to fit the mini-jack

receptacle.

Basic Operating Controls

The following explanations will help you get

familiar with the features and controls. When

a function is available on both the front panel

and the remote, a number (see front panel

illustration) and a letter (see remote control

illustration) are shown in the instructions. For

example, to change from the AM to FM band,

you can either press the front panel button or

use the button on the remote. When only one

identifier appears, that control is available only

on the front panel or the remote, but not both.

NOTE: Controls used for tuning the AM/FM

receiver are described in the next sections of

this manual.

Power Button and

Power LED

The POWER button is located on the front panel

of the RT-02 and is not duplicated on the re-

mote control. Push the button IN to turn the

unit on. The LED above the switch and the front

panel display will light up. Push the button

again (returning it to the OUT position), to turn

the unit off.

NOTE: If you are using a switched outlet on

another component to power the RT-02 or if

you are using the 12 volt trigger feature, leave

the POWER switch in the ON position.

Remote Sensor

This front panel sensor receives infrared sig-

nals from the remote control. Make sure you

do not accidentally block this sensor with cables

or accessories.

RT-02 AM/FM Stereo Tuner

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel rt 02 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info