Bedienungsanleitung Rotorazer Platinum (Seite 4 von 9) (Englisch)

588333

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the state of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are: Lead from lead-based

paint, crystalline silica from bricks and cements and other masonry products, and Arsenic and

chromium from chemically-treated Lumber.

Safety instructions for all saws

a) DANGER: Keep hands away from cutting area and the blade. Keep your second hand on

the body of the motor housing. If both hands are holding the saw, they cannot be

cut by the blade.

b) Do not reach underneath the work piece. The guard cannot protect you from the blade

below the work piece.

c) Adjust the cutting depth to the thickness of the work piece. Less than a full tooth of the blade

teeth should be visible below the work piece.

d) Never hold the work piece being cut in your hands or across your leg. Secure the work piece to

a stable platform. It is important to support the work piece properly to minimize body exposure,

blade binding, or loss of control.

e) Hold the Rotorazer Saw® Platinum by insulated gripping surfaces when performing an opera-

tion where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire

will also make exposed metal parts of the Rotorazer Saw® Platinum "live" could/may shock the

operator.

f) When ripping always use a rip fence or straight edge guide. This improves the accuracy of cut

and reduces the chance of blade binding.

g) Always use blades with the correct size and shape (diamond versus round) of arbor holes

that adapt perfectly to the hole they are inserted.

Blades that do not match the mounting hardware of the saw will run eccentrically,

causing loss of control.

h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were

specially designed for your saw, for optimum performance and safety of operation.

Further safety instructions for all saws

Causes and operator prevention of kickback:

• Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the work piece toward the operator;

• When the blade is pinched or bound tightly by the kerf closing down, the blade stalls

and the motor reaction drives the unit rapidly back toward the operator;

• If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade

can dig into the top surface of the wood causing the blade to climb out of the kerf and jump

back toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions

and can be avoided by taking proper precautions as given below.

a) Maintain a firm grip with both hands on the saw and position your arms to resist kickback

forces. Position your body to either side of the blade, but not in line with the blade. Kickback

could cause the saw to jump backwards, but kickback forces can be controlled by the operator,

if proper precautions are taken.

b) When blade is binding, or when interrupting a cut for any reason, release the trigger and hold

the saw motionless on the work piece until the blade comes to a complete stop. Never attempt

to remove the saw from the work piece or pull the saw backward while the blade is in motion

or kickback may occur. Investigate and take corrective actions to eliminate the cause of

blade binding.

SAFETY WARNINGS

c) When restarting a saw in the work piece, center the saw blade in the kerf/groove and check that

saw teeth are not engaged into the material. If saw blade is binding, it may walk up or kickback

from the work piece as the saw is restarted.

d) Provide support for large panels to minimize the risk of blade pinching and kickback. Large

panels tend to sag under their own weight. Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow

kerf/groove causing excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must be tight and secure before making cut.

If blade adjustment shifts while cutting, it may cause binding and kickback.

g) Use extra caution when making a "plunge cut" into existing walls or other blind areas.

The protruding blade may cut objects that can cause kickback.

Safety instructions

a) Check blade guard for proper closing before each use. Do not operate the saw if blade guard

does not move freely and close instantly. Never clamp or tie the blade guard into the open

position. If saw is accidentally dropped, blade guard may be bent. Raise the blade guard by the

sole plate and make sure it moves freely and does not touch the blade or any other part, in all

angles and depths of cut.

b) Check the operation of the blade guard spring. If the guard and the spring are not operating

properly, they must be serviced before use. Blade guard may operate sluggishly due to

damaged parts, sticky residue, or an accumulation of debris.

c) Blade guard may be retracted manually only for special cuts such as "plunge cuts" and

"compound cuts." Raise blade guard by sole plate and as soon as blade enters the material,

the lower guard must be released. For all other sawing, the blade guard should operate

automatically.

d) Always observe that the blade guard is covering the blade before placing saw down on bench

or floor. An unprotected, spinning blade will cause the saw to walk backwards, cutting whatever

is in its path. Be aware of the time it takes for the blade to stop spinning after switch is released.

- DO NOT use any abrasive wheels.

- Use only blade diameter(s) in accordance with the markings.

WARNING

Working with some kinds of wood and metal or with paint that contains lead can generate

harmful or toxic gases that are a risk for the user and other people in the work area. Always

wear suitable personal protection and keep people from getting too close to the work area.

TECHNICAL DATA

Voltage 120 volt – 60 Hz

Watt 420 watt

No load Speed 4500 rpm

Blade size 85mm

Max cutting depth 1 inch

SAFETY WARNINGS

Rotorazer Platinum Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info