Bedienungsanleitung Rowenta DG8020 (Seite 7 von 46) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

739334

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

11 • Cleaning the generator

The Iron soleplate: You can clean the

soleplate of your iron, once it has cooled down,

with a damp cloth or sponge.

The base unit: Clean the plastic parts of the

appliance occasionally with a soft cloth.

12 •

Rinsing the boiler

Your generator is equipped with an orange

“boiler rinse” warning light (fig.9) that flashes

on the control panel after about 10 uses.

You can continue ironing normally but

remember to rinse the boiler first, the next

time that you use it.

Before attempting to rinse the boiler of your

generator, it is essential to leave it to cool for

at least 2 hours in order to avoid any risk of

scalding.

Place your steam generator on the edge of your

sink, with the iron to one side, standing on its

heel. Remove the boiler rinse cap cover (fig.14).

Using a coin, gently unscrew the boiler rinse cap

(fig.15).

With the rinsing accessory

: it will make it

easier to rinse the boiler as the generator will

need less handling. Your rinsing accessory has

been designed to work on a wide range of taps.

Choose the one best suited to your tap (a or

b)(fig.16). Place the plastic nozzle of the

rinsing pipe into the hole of the boiler and turn

gently to the right until it locks (fig.17). The

outlet of this nozzle must be positioned over

the sink (fig.18). Connect the rubber end ¡ of

the rinsing pipe to a cold tap (R). Turn the tap

on gently and gradually and let cold water run

through the rinsing pipe into the sink for about

1 minute (fig.19). Switch off the tap and

remove the rinsing pipe.

With the rinsing accessory

Gently unscrew the boiler rinse plug (fig.14).

Holding your steam generator in a tilted

position, and using a jug, fill the boiler (in the

base unit) with 1/4 litre of tap water.

Shake the base unit for a few moments and

then empty it completely over your sink.

To obtain the best result, we recommend that

this operation is done twice.

ATTENTION: Do not use descaling agents

for rinsing out the boiler, as they could

damage it.

Do not use any cleaning or descaling

products for cleaning the soleplate or the

base-unit. Never hold the iron or the base

unit under the tap.

MAINTENANCE AND CLEANING

Before cleaning or rinsing the boiler, ensure that the appliance is unplugged and that the

soleplate and the iron rest have cooled down for at least 2 hours, in order to avoid any risk

of scalding.

The next time you use the generator, hold

down the “restart” (fig.20) button to turn

off the orange light. .

Close the water tank. Press on the on / off

switch (fig.4). It is flashing. Press the “Restart”

button. The generator and the iron are ready to

iron when the steam ready indicator light is lit

and the iron thermostat dial light has gone out.

10 • Storing your generator

Press the illuminated on/off switch O/I and

unplug the generator. Place the iron on the iron

rest plate. Press the cord reel button (depen-

ding on model) and guide the cord with your

hand (fig.12) and store the steam cord.

Leave the iron to cool down for 1 hour before

putting it away if it is stored in a cupboard or

confined space.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rowenta DG8020 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info