Bedienungsanleitung Rowenta DZ5920 (Seite 8 von 71) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

739313

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

(*) Depending on model

After a few seconds water will emerge from the soleplate, rinsing any impurities

out of the steam chamber (fig.5).

Move the steam control to steam position after approx.

1 minute. Plug in the iron and allow the iron to heat up again. Wait until the

remaining water has evaporated. Unplug from the mains and allow the iron to fully

cool down.

USE

4 • Filling the water tank

IMPORTANT Before filling the water tank, unplug the iron and set the steam

control to dry position .

Tilt the iron. Open the filling inlet (fig.6). Pour in water up to the max mark (fig.7).

Close the filler inlet (fig.8) and return the iron to the horizontal.

5 • Setting the temperature

Set the iron temperature to suit the type of material using the temperature control

dial (fig.3).

Temperature control*: The temperature control light indicates that the soleplate is

heating up. When the temperature control light goes off (fig.9), the set temperature

is reached and you can begin ironing.

set temperature is reached and you can begin ironing.

Electronic temperature control*: The traffic lights tell you whether the soleplate is

at the selected temperature (fig.10).

IMPORTANT The iron takes longer to cool down than to heat up. We

recommend that you start with fabrics to be ironed at a low temperature.

For mixed fabrics set the temperature for the most delicate fabric.

TIP Always spray starch onto the reverse side of the fabric to be ironed.

6 • Dry ironing

Set the variable steam control to (fig.11) and set the temperature to suit the

type of material (care points •, ••, •••).

7 • Steam ironing

You can steam iron from temperature setting •• upwards.

Steam function* The steam quantity can be set to between no steam (minimum

steam quantity) and (maximum steam quantity) (fig.12). We recommend setting

to maximum steam quantity only when the iron is at temperature setting •••.

Auto Steam function* Set the steam button to (fig.13) and the steam quantity will

adjust automatically to the soleplate temperature

8 • Shot of steam (from temperature setting •• upwards)

IMPORTANT Leave an interval of 4 seconds between each shot and wait until

the flow of steam is finished before standing the iron on its heel.

Press the shot of steam button to generate a powerful jet of steam and remove

stubborn creases (fig.14).

Ironing label Fabric

Temperature

control

Synthetic fibres, e.g. viscose,

polyester…

•

Silk, wool

••

Cotton, linen

•••

YELLOW The soleplate is still too cold for the selected material.

GREEN The soleplate is at the right temperature for the selected material.

RED The soleplate is still too hot for the selected material.

AUTO- OFF The automatic electronic cut-out* is active.

1103910025 DZ5000 D1 _110x220mm 15/03/13 11:14 Page3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rowenta DZ5920 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info