Bedienungsanleitung Rowenta PU3030 (Seite 6 von 94) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

726644

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

Frequency of cleaning/replacing the lters :

Filter Clean/replace Frequency Filter codes

Pre filter Clean Every 2 months

2in1 Active Carbon & Allergy+ filter Replace Every 12 months XD6231

NanoCaptur+ filter (only PU3040 model) Replace

Color changing (see

color chart on filter)

or every 12 months in

case of no saturation.

XD6082

These figures are based on tests in which the air purifier is used for 8 hours per day in quiet mode.

You may need to replace the filters more often depending on the air quality and how often the air purifier

is used. The filter replacement indicator (7) will turn on when the filters need to be replaced. To replace the

filters, please refer to the section “Disassembling / Reassembling filters”.

Important! When the filter replacement indicator turns on, check whether the filters need to be replaced.

• When the lter replacement indicator (7) turns on, this indicates that the 2in1 Active Carbon & Allergy+

lter needs to be replaced.

• The pre-lter can be cleaned with a vacuum cleaner or rinsed in water.

Important: Resetting the filter

After replacing the filter, press the brightness button (4) for 3 seconds to reset the filter settings.

Performing a force reset:

If you replace a filter before the end of its lifespan, press the brightness button (4) for 3 seconds to reset the

filter settings.

Caution :

If the granules become "white opaque", filter needs to be removed from the purifier until the granules

become transparent again.

If the opaque aspect persists, filter need to be changed.

If the granule become "crumbly", filter need to be changed.

The appliance efficiency can be reduced if the pre-filter is not cleaned regularly.

Never use a pre-filter that is still damp.

The pre-filter is the only filter which can be re-used and washed with water. The 2in1 Active Carbon & Allergy+ filter

cannot be cleaned and re-used. Never wash with water. The 2in1 Active Carbon & Allergy+ filter must be replaced

after the end of its lifespan. For optimum performance of the appliance, only use filters provided by Rowenta. If

the Nanocaptur+ filter granules become opaque white or/and crumbly, the filter needs to be changed.

Please note: certain filters may emit a temporary slight odour, due to the transport and storage conditions.

« TIPS FOR CHANGING FILTERS »

• Avoid handling used lters if you suer from allergies or asthma.

• Wear gloves when changing the lters, or wash your hands well afterwards.

• Put used lters directly into a closed, air-tight bag before throwing them away to avoid

spreading pollutants.

Pollution sensors

The particle sensor need to be cleaned regularly (every 2 months) and appropriately.

Make sure you turn off and unplug the appliance before cleaning the pollution sensors and follow the

recommendations below:

1. Clean the air inlet and outlet using a soft brush or cloth.

2. Open the sensor cover located on the left hand side of the appliance.

3. Lightly wet a cotton swab and remove any dust from the lens and the inlet/outlet. Wipe using a dry cotton swab.

4. Clean the sensor using a soft brush or vacuum cleaner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rowenta PU3030 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info