The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Engine displacement 46 cm
3
Maximum engine capacity 2 kW
Bar length 36 cm
Cutter rail length 16” (40 cm)
Chain pitch (3/8”), 9.525 mm
Chain thickness 1.27 mm
Idling speed 3300 ± 200 rpm
Maximum speed with cutting equipment 11000 rpm
Tank capacity 550 ml
Oil tank capacity 260 ml
Anti-vibration function Yes
Chain wheel teeth 7 x 9.525 mm
Chain brake Yes
Clutch Yes
Automatic chain lubrication Yes
Low-kickback chain -
Net weight without chain and chain bar 5.5 kg
Net weight (dry) 7 kg
Fuel consumption (specific) 560 g / kWh
L
PA
sound pressure level (ISO 22868) 99 dB(A)
K
PA
uncertainty 3 dB(A)
L
WA
sound power level measured
(ISO 22868) 111 dB(A)
K
WA
uncertainty 3 dB(A)
L
WA
sound power level guaranteed
(ISO 2000/14/EC) 114 dB(A)
A
hv
vibration (front handle)
(ISO 22867) 7.5 m/s
2
K
hv
uncertainty 1.5 m/s
2
A
hv
vibration (rear handle)
(ISO 22867) 7.0 m/s
2
K
hv
uncertainty 1.5 m/s
2
Chain type Carlton N1C-BL-57-EB
Bar type Kangxin AP16-57-507P
Spark plug L8RTF/NHSP LD
Keep the noise emissions and vibrations to a
minimum.
n Only use appliances which are in perfect working
order.
n Service and clean the appliance regularly.
n Adapt your working style to suit the appliance.
n Do not overload the appliance.
n Have the appliance serviced whenever
necessary.
n Switch the appliance off when it is not in use.
n Wear protective gloves.
5. Before starting the equipment
Important: Do not start the engine until the saw
is fully assembled.
Important: Wear protective gloves at all times
when handling the chain.
5.1 Fit the chain bar
To ensure that the bar and the chain are supplied
with oil, USE ONLY THE ORIGINAL BAR. The oiling
hole (Fig. 2/Item A) must be kept clear of dirt and any
build-up of residue.
1. Make sure the Chain brake lever is pulled back
into the DISENGAGED position (Fig. 3A).
2. Remove the two bar fastening nuts (B). Remove
the cover (Fig. 3B).
3. Using a screwdriver, run the adjustment screw (D)
COUNTERCLOCKWISE until the TANG (E)
(projecting prong) is to the end of its travel toward
the clutch drum and sprocket (Fig. 3C).
4. Fit the open end of the chain bar over the die bar
pins (F) (Fig. 3D).
5.2 To install saw chain
1. Spread chain out in a loop with cutting edges (A)
pointing CLOCKWISE around loop (Fig. 4A).
2. Slip the chain around the sprocket (B) behind the
clutch (C). Make sure the links fit between the
sprocket teeth (Fig. 4B).
3. Guide the drive links into the groove (D) and
around the end of the bar (Fig. 4B).
NOTE: The saw chain may droop slightly on the lower
part of bar. This is normal.
21
GB
